Re: Seeburg STD4 - not playing side A

On Sunday, November 20, 2022 at 11:01:51 AM UTC-6, John Robertson wrote:
> On 2022/11/19 8:15 a.m., Deanie Spikes wrote: 
> > On Wednesday, November 16, 2022 at 9:48:36 AM UTC-6, John Robertson wrote: 
> >> On 2022/11/16 5:49 a.m., Deanie Spikes wrote: 
> >>> On Friday, March 5, 2004 at 6:14:08 PM UTC-6, Andy Guthrie wrote: 
> >>>> Well thanks for the warning... Unfortunately, it's said and done. I 
> >>>> straightened out the contact and side A is now back in the game. 
> >>>> Everything is back to its original state, plus side A is working, but I 
> >>>> am getting the occasional wrong selection error. 
> >>>> The most common mistake seems to be it reading a 5 as a 2 (i.e., playing 
> >>>> 126 instead of 156). 
> >>>> Until I scrape together the cash for the service manuals... Any suggestions? 
> >>>> Happy Seeburg Olympian Owner wrote: 
> >>>>> the strip is called a Tormat :) 
> >>>>> 
> >>>>> i wold not remove the tormat unless you have the manual!!! the pice that 
> >>>>> scans the tormat if i remember right can be removed seperatly <consult the 
> >>>>> manual> 
> >>>>> 
> >>>>> Jim w 
> >>>>> "Andy Guthrie" <[email protected]> wrote in message 
> >>>>> news:[email protected]... 
> >>>>> 
> >>>>>> Well, here's an update. 
> >>>>>> I can only assume that I was mistaken about seeing side A work at the 
> >>>>>> previous owners house. I pulled the front off and found that the contact 
> >>>>>> for the A side of the record (where it scans the magnetic o-rings) is 
> >>>>>> bent. I am going to try to remove the strip of magnetic o-rings (gee, 
> >>>>>> can you tell I'm a newbie with these terms?) and straighten out the 
> >>>>>> sensor. I sure hope this works... 
> >>>>>> 
> >>>>>> 
> >>>>>> Andy Guthrie wrote: 
> >>>>>> 
> >>>>>>> Hi everyone- my first post. 
> >>>>>>> I have officially started my jukebox "collection" by buying a Seeburg 
> >>>>>>> STD4 "Mardi Gras" model. 
> >>>>>>> Things seem to be ok, except I cannot play side "A" of the records. All 
> >>>>>>> of the side B's (the 2xx selections) work fine. 
> >>>>>>> I followed Tony Miller's troubleshooting guide, and connected the 
> >>>>>>> negative side of a D battery to the tormat lead, and the machine did 
> >>>>>>> pick up each disc, but again, only played the B sides. The A sides were 
> >>>>>>> working when I checked out the machine prior to buying it, so I get the 
> >>>>>>> feeling that a wire may have fallen loose during the move. 
> >>>>>>> When I punch in a 1xx selection, the mechanism scans twice and then 
> >>>>> 
> >>>>> parks. 
> >>>>> 
> >>>>>>> Any ideas what might cause the skipping of the 1xx selections? 
> >>>>>>> 
> >>>>>>> Thanks! 
> >>>>>>> 
> >>>>>> 
> >>>>> 
> >>>>> 
> >>> Hi, Andy! I realize that I am replying to an ancient post, but I figured it wouldn't hurt to try. I have the same issue with the exact same jukebox. You mentioned that you straightened out the contact for side A selections because it was slightly bent. Could you please explain where this contact is located? I'm not sure where to look! Thanks, so much! 
> >> Check connections in all the plugs related to the keyboard and Tormat 
> >> (move outward if those are all good). You may find a damaged Molex pin, 
> >> or a pin that is pushed back relative to the others so it is no longer 
> >> making contact. 
> >> 
> >> This is not uncommon... 
> >> 
> >> John :-#)# 
> >> --
> > John, thanks for the advice! Please forgive my ignorance, but do I need to remove the mechanism in order to check the connections in all the plugs related to the keyboard and Tormat and look for damaged Molex pins? When I got the jukebox, it was not working. Lights came on, but the mechanism was stuck all the way to the right (when looking from the back). After researching a LOT, I felt confident enough to remove the mechanism, which I did. I oiled the motor, and manually turned the coupling until a full cycle was complete. It seemed to have been stuck in the play position. I sprayed the contacts (only the few that I saw....I'm sure I missed some) with contact cleaner. I replaced everything, and it started scanning! I did the battery test, and it picked up every #2 side, but none of the #1 sides. 
> > 
> > Sorry for rambling, but I just wanted to explain what I had done. So, back to my original question...do I need to remove the mechanism again in order to check for damaged connections or pins? Stupid question #2: is the tarmat part of the whole mechanism that comes out? Where, exactly, is it? Thanks for tolerating my ignorance!
> No, you shouldn't have to remove the mechanism to check the connections. 
> I'm thinking checking at the control center first. 
> 
> As for not playing one side, do check the manual and make sure you have 
> set up the Tormat Readout contacts correctly. And the the Tormat is 
> aligned correctly, and that the Reversing Switch on the mechanism is 
> operating correctly - that the circuit to the readout switches - if 
> present - is exchanged correctly. 
> 
> I hope you have the manual! It should go into detail on troubleshooting 
> and adjustments.
> John :-#)# 
> -- 
> (Please post followups or tech inquiries to the USENET newsgroup) 
> John's Jukes Ltd. 
> #7 - 3979 Marine Way, Burnaby, BC, Canada V5J 5E3 
> (604)872-5757 (Pinballs, Jukes, Video Games) 
> www.flippers.com 
> "Old pinballers never die, they just flip out."
Thank you, John.  I have the manual, and  have printed out several adjustment pages.  Hopefully, I'll be able to make some progress!