Re: spreadlogd 1.4.2, spread 3.16.2, FreeBSD 4.6-RELEASE

On Wed, Sep 04, 2002 at 06:19:05PM -0400, George Schlossnagle wrote:
> Can you start it up as
> 
> gdb /path/to/httpd
> 
> r  -X
> 
> then when it segafults do a
> 
> bt full
> 
> and send the output?

gdb /usr/local/sbin/spread
GNU gdb 4.18 (FreeBSD)
Copyright 1998 Free Software Foundation, Inc.
GDB is free software, covered by the GNU General Public License, and you are
welcome to change it and/or distribute copies of it under certain conditions.
Type "show copying" to see the conditions.
There is absolutely no warranty for GDB.  Type "show warranty" for details.
This GDB was configured as "i386-unknown-freebsd"...(no debugging symbols found)...
(gdb) run -c /usr/local/etc/spread.conf
Starting program: /usr/local/sbin/spread -c /usr/local/etc/spread.conf
/===========================================================================\
| The Spread Toolkit.                                                       |
| Copyright (c) 1993-2001 Spread Concepts LLC                               |
| All rights reserved.                                                      |
|                                                                           |
| The Spread toolkit is licensed under the Spread Open-Source License.      |
| You may only use this software in compliance with the License.            |
| A copy of the license can be found at http://www.spread.org/license       |
|                                                                           |
| This product uses software developed by Spread Concepts LLC for use       |
| in the Spread toolkit. For more information about Spread,                 |
| see http://www.spread.org                                                 |
|                                                                           |
| This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF     |
| ANY KIND, either express or implied.                                      |
|                                                                           |
| Spread is developed at Spread Concepts LLC and the Center for Networking  |
| and Distributed Systems, The Johns Hopkins University.                    |
|                                                                           |
| Creators:                                                                 |
|    Yair Amir             [email protected]                              |
|    Michal Miskin-Amir    [email protected]                        |
|    Jonathan Stanton      [email protected]                              |
|                                                                           |
| Major Contributors:                                                       |
|    Dan Schoenblum   [email protected] - Java Interface Developer.       |
|    John Schultz     [email protected] - contribution to process group |
|                                             membership.                   |
|    Theo Schlossnagle [email protected] - Perl library and Skiplists      |
|                                                                           |
| Special thanks to the following for providing ideas and/or code:          |
|    Ken Birman, Danny Dolev, Mike Goodrich, Ben Laurie,                    |
|    David Shaw, Robbert VanRenesse.                                        |
|                                                                           |
| For a full list of contributors, see Readme.txt in the distribution.      |
|                                                                           |
| WWW:     www.spread.org     www.cnds.jhu.edu    www.spreadconcepts.com    |
| Contact: [email protected]                                                |
|                                                                           |
| Version 3.16.02 Built 02/Apr/2002                                         |
\===========================================================================/
ip_init: using file: /usr/local/etc/spread.access_ip
Conf_init: using file: /usr/local/etc/spread.conf
Successfully configured Segment 0 [208.187.213.63:4803] with 3 procs:
        mysql2.freecommunityÃ: 208.187.213.32
        web1.freecommunity.cÃ: 208.187.213.10
        web2.freecommunity.cÃ: 208.187.213.31
Finished configuration file.
Conf_init: My name: mysql2.freecommunityÃ, id: 208.187.213.32, port: 4803
Spread: setugid and chroot successeful
Membership id is ( -792996576, 1031185006)
--------------------
Configuration at mysql2.freecommunityà is:
Num Segments 1
        2       208.187.213.63    4803
                mysql2.freecommunityà  208.187.213.32
                web2.freecommunity.cà  208.187.213.31
====================
++++++++++++++++++++++
Num of groups: 0
(no debugging symbols found)...(no debugging symbols found)...
Program received signal SIGSEGV, Segmentation fault.
0x0 in ?? ()
(gdb) bt full
#0  0x0 in ?? ()
No symbol table info available.
(gdb)


-- 
Michael Parson
[email protected]