Re: Install mod perl

Il 18/05/2011 19.22, André Warnier ha scritto:
> marco wrote:
>> Il 17/05/2011 22.33, André Warnier ha scritto:
>>> marco,
>>>
>>> under which version/distribution of Linux are you doing this ?
>>> (the answer I am looking for is something like Debian or Ubuntu or 
>>> RedHat..)
>>>
>>> The reason I am asking you, is that each of these distributions has 
>>> a "package" system, which you can probably use to install apache and 
>>> perl and mod_perl using just a couple of commands, and not have to 
>>> bother doing it "the hard way".
>>>
>>> See the answer of Cosimo Streppone previously today in the same 
>>> mod_perl list, subject : Ubuntu and mod_perl.
>>
>>
>> I did some step ahead but mod_perl's installation doesn't work.
>> I remember that i want to install it into apache like dynamic module, 
>> so I have installed apache and it runs well.
>> I did these step (in directory "mod_perl-2.0.5"):
>> 1.  $perl Makefile.PL MP_APXS=/usr/local/apache/bin/apxs DO_HTTPD=1 
>> USE_APACI=1 EVERYTHING=1
>>      This phase goes ok but it prints some warnings:
>> *[warning] mod_perl dso library will be built as mod_perl.so
>> [warning] You'll need to add the following to httpd.conf:
>> [warning]
>> [warning]   LoadModule perl_module modules/mod_perl.so
>> [warning]
>> [warning] depending on your build, mod_perl might not live in
>> [warning] the modules/ directory.
>>
>> [warning] Check the results of
>> [warning]
>> [warning]   $ /usr/local/apache/bin/apxs -q LIBEXECDIR
>> [warning]
>> [warning] and adjust the LoadModule directive accordingly.
>> *
>> 2. I go ahead and i type:
>> $make
>> but it prints me some error:
>> */usr/bin/ld: cannot find -lperl
>> collect2: ld returned 1 exit status
>> make[1]: *** [mod_perl.so] Error 1
>> make[1]: Leaving directory 
>> `/home/marcolino/mod_perl-2.0.5/src/modules/perl'
>> make: *** [modperl_lib] Error 2*
>>
>> How can I fix this problem?
>> Please someone help me!!!!
>>
> Well, we try.
> Why do you not save yourself all that aggravation and do as Cosimo 
> suggested earlier in another thread :
>
> pre-requisite : disable the Apache which you tried to compile/install 
> by hand, then..
>
> On Wed, 18 May 2011 00:05:46 +1000, Tom Kane <[email protected]> 
> wrote:
>
> > I now want to add mod_perl (in the .so form) to apache2.
> > [...]
> > I am still new in the Unix/Linux environment -- at least from the
> > standpoint of installing systems software -- so I am sure I am missing
> > something.
>
> Hi Tom,
>
> if you don't need to compile the software yourself,
> and you're just starting, I would suggest an easy path:
>
>   # Install the relevant packages
>   sudo apt-get install apache2 apache2-mpm-prefork
>   sudo apt-get install libapache2-mod-perl2 libapache2-mod-apreq2
>
>   # Enable the apreq and mod perl modules
>   a2enmod apreq
>   a2enmod perl
>
>   # Restart apache
>   /etc/init.d/apache2 restart
>
I fixed the problem not in this way but i installed a perl packet that 
was necessary for the compilation.
I hope was that the problem.
I type:
$perl Makefile.PL MP_APXS=/usr/local/apache/bin/apxs
$make
$make install
and it was ok
$/usr/local/apache/bin/apachectl start
and it was ok.

Now, for try if mod_perl works i must write some module.
Let's see!!!

Thanks for suggests of all users answered to me!!!!