ide-scsi -> write_g1: scsi sendcmd: fatal error

cdrecord using ide-scsi returns an error that I don't understand.  The
burner can be used with dev=ATA:0,1,0, so I can't see how it is a device
problem. 

I am using ide-scsi for rscsi compatibility and remote burning. 

The error follows:
# cdrecord dev=0,0,0 -dao -data dsl-1.1.iso 
Cdrecord-ProDVD-ProBD-Clone 2.01.01a34 (i686-pc-linux-gnu) Copyright
(C) 1995-2007 Jörg Schilling scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.5.34
Using libscg version 'schily-0.9'.
Device type    : Removable CD-ROM
Version        : 0
Response Format: 2
Capabilities   : 
Vendor_info    : 'SONY    '
Identifikation : 'CD-RW  CRX230E  '
Revision       : 'QYS1'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE FORCESPEED 
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P
RAW/R96R Starting to write CD/DVD/BD at speed 4 in real SAO mode for
single session. Last chance to quit, starting real write    0 seconds.
Operation starts. Turning BURN-Free off
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
cdrecord: No such device or address. write_g1: scsi sendcmd: fatal error
CDB:  2A 00 FF FF FF 89 00 00 1F 00
cmd finished after 0.000s timeout 200s
write track pad data: error after 63488 bytes
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
cdrecord: No such device or address. read buffer cap: scsi sendcmd:
fatal error CDB:  5C 00 00 00 00 00 00 00 0C 00
cmd finished after 0.000s timeout 200s
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
cdrecord: No such device or address. write_g1: scsi sendcmd: fatal error
CDB:  2A 00 00 00 00 00 00 00 1F 00
cmd finished after 0.000s timeout 200s
write track data: error after 0 bytes
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
cdrecord: No such device or address. test unit ready: scsi sendcmd:
fatal error CDB:  00 00 00 00 00 00
cmd finished after 0.000s timeout 200s
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
cdrecord: No such device or address. flush cache: scsi sendcmd: fatal
error CDB:  35 00 00 00 00 00 00 00 00 00
cmd finished after 0.000s timeout 200s
Trouble flushing the cache
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
<snip>
cdrecord: No such device or address. Cannot send SCSI cmd via
ioctl. cdrecord: faio_wait_on_buffer for writer timed out.
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
cdrecord: No such device or address. prevent/allow medium removal: scsi
sendcmd: fatal error CDB:  1E 00 00 00 00 00
cmd finished after 0.000s timeout 200s
cdrecord: No such device or address. Cannot send SCSI cmd via ioctl.
<snip>
cdrecord: No such device or address. Cannot send SCSI cmd via
ioctl. cdrecord: No such device or address. prevent/allow medium
removal: scsi sendcmd: fatal error CDB:  1E 00 00 00 00 00
cmd finished after 0.000s timeout 200s

The same error is returned with the more recent 2.01.01_alpha57.

# uname -r 
2.6.24-gentoo-r8

Any clues as to the cause of the error.

Regards 
Fog_Watch
-- 
Lose wait.  Get Gentoo.


-- 
To UNSUBSCRIBE, email to [email protected]
with a subject of "unsubscribe". Trouble? Contact [email protected]