dvd+rw-tools 7.1, Blu-Ray, and INVALID FIELD IN CDB on session close

Hello,

Please see the issue I posted here with my new Pioneer BDR-205 fw 1.03:
http://club.myce.com/f143/cant-close-session-bdr-205-external-macally-cm-s525u-308505/

I then found the following posts on this ML explaining quite similar
problems:
http://www.mail-archive.com/[email protected]/msg13071.html
http://www.mail-archive.com/[email protected]/msg13093.html

I followed the advice in the last post to try cdrskin instead, and this
is what happened (0.7.6.pl00-2):

  $ mkisofs -rJ . | cdrskin -v dev=/dev/sr1 blank=format_if_needed [tried with speed=4 also] -

  cdrskin 0.7.6 : limited cdrecord compatibility wrapper for libburn
  cdrskin: verbosity level : 1
  cdrskin: NOTE : greying out all drives besides given dev='/dev/sr1'
  cdrskin: scanning for devices ...
  I: -input-charset not specified, using utf-8 (detected in locale settings)
  [...]
  cdrskin: status 1 burn_disc_blank "The drive holds a blank disc"
  Current: BD-R sequential recording
  Track 01: data  unknown length
  Total size:       0 MB (00:00.00) = 0 sectors
  Lout start:       0 MB (00:02/00) = 0 sectors
  Starting to write CD/DVD at speed MAX in real TAO mode for single session.
  Last chance to quit, starting real write in   0 seconds. Operation starts.
  Waiting for reader process to fill input buffer ... input buffer ready.
  Starting new track at sector: 0
  Track 01:    5 MB written (fifo  98%) [buf  25%]   4.0x.  0.04% done, estimate finish Mon Feb  8 11:09:41 2010
  Track 01:    7 MB written (fifo  99%) [buf  40%]   1.3x.cdrskin: FATAL : SCSI error on write(3632,16): [5 21 02] Invalid address

  cdrskin: thank you for being patient for 20 seconds
  Track 01: Total bytes read/written: 7471104/7438336 (3632 sectors).
  Writing  time:  19.746s
  Cdrskin: fifo had 5727 puts and 3679 gets.
  Cdrskin: fifo was 0 times empty and 1160 times full, min fill was 97%.
  Min drive buffer fill was 0%
  cdrskin: burning failed
  cdrskin: FATAL : burning failed.

No errors in dmesg (aside from those related to inserting the blank
disc).

Then I tried the same command again:

  [...]
  cdrskin: ... scanning for devices done
  cdrskin: status 3 BURN_DISC_APPENDABLE "There is an incomplete disc in the drive"
  Current: BD-R sequential recording
  cdrskin: beginning to burn disc
  cdrskin: status 3 BURN_DISC_APPENDABLE "There is an incomplete disc in the drive"
  Current: BD-R sequential recording
  Track 01: data  unknown length
  Total size:       0 MB (00:00.00) = 0 sectors
  Lout start:       0 MB (00:02/00) = 0 sectors
  Starting to write CD/DVD at speed MAX in real TAO mode for single session.
  Last chance to quit, starting real write in   0 seconds. Operation starts.
  Waiting for reader process to fill input buffer ... input buffer ready.
  Starting new track at sector: 3616
  cdrskin: thank you for being patient for 3 seconds                     cdrskin: FATAL : SCSI error on write(0,16): [5 21 02] Invalid address

  Track 01: Total bytes read/written: 32768/0 (0 sectors).
  Writing  time:  3.825s
  Cdrskin: fifo had 2095 puts and 47 gets.
  Cdrskin: fifo was 0 times empty and 0 times full, min fill was 100%.
  Min drive buffer fill was 50%
  cdrskin: burning failed
  cdrskin: FATAL : burning failed.

So I'm baffled how to simply write an ISO filesystem to a Blu-Ray disc
without errors...

-- 
Ryan C. Underwood, <[email protected]>


-- 
To UNSUBSCRIBE, email to [email protected]
with a subject of "unsubscribe". Trouble? Contact [email protected]