Re: stop (restart or resume) continue backup paused or stopped.

thanks for the response.  I understood better.

On Mon, Nov 25, 2024 at 7:29 PM Bill Arlofski via Bacula-users <
[email protected]> wrote:

> On 11/25/24 3:49 PM, Jose Alberto wrote:
> > Hello. Bacula 15.0.2 Debian 11.
> >
> > I have a full Job that weighs 2.4TB.  When I was going for 1.6 I
> executed "stop" in bconsole.
> >
> > Then run resume (but I have doubts if "restart" was ideal). But it seems
> like it was starting from 0 and not from the 1.6TB
> > it had,
>
> Hello Jose,
>
> What you have show from the current logs looks perfectly fine.
>
>
> JobID: 154432 terminates Incomplete:
> ----8<----
> Termination:            Backup failed -- Incomplete
> ----8<----
>
>
> Then, when restarted, it shows that it is restarting the incomplete Backup
> (same) JobID 154432, and that it knows about the
> 1,821,115 files that were backed up before the job was stopped:
> ----8<----
> srvlnxbacula-dir JobId 154432: Restart Incomplete Backup JobId 154432,
> Job=sve0000-071-job.2024-11-24_01.00.00_18
> srvlnxbacula-dir JobId 154432: Found 1821115 files from prior incomplete
> Job.
> ----8<----
>
>
> And then it continues where it left off as if it work working on a normal
> backup job:
> ----8<----
> srvlnxbacula-dir JobId 154432: Connected to Storage "MSL3040" at
> 10.0.0.190:9103 with TLS
> srvlnxbacula-sd JobId 154432: 3307 Issuing autochanger "unload Volume
> DBP084L7, Slot 37, Drive 0" command.
> srvlnxbacula-dir JobId 154432: Using Device "DRIVE0" to write.
> srvlnxbacula-dir JobId 154432: Connected to Client "sve0000-071-fd" at
> 10.0.0.71:9102 with TLS
> srvlnxbacula-dir JobId 154432: Sending Accurate information to the FD.
> ----8<----
>
>
> > If start from 0. There is no point in running stop and then resume.  or
> I'm wrong.
>
> As you can see from above, it does not start that 0.  It is possible that
> a `status client` or a `status storage` may not
> indicate the full amount of files/bytes when a job is resumed, but the end
> result in the job summary, and the data actually
> backed up is correct.
>
>
> > Difference between resume and restart?
>
> They are the same.
>
> For the `resume` command, the manual states:
> ----8<----
> *resume*
>
> The resume command does exactly the same thing as a restart command, but
> for some users the name may be more logical because
> in general the restart command is used to resume running a Job that was
> incomplete.
> ----8<----
>
>
> Hope this helps,
> Bill
>
> --
> Bill Arlofski
> [email protected]
> _______________________________________________
> Bacula-users mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/bacula-users
>


-- 
#############################
#   Sistema Operativo: Debian      #
#        Caracas, Venezuela          #
#############################

_______________________________________________
Bacula-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bacula-users