[PATCH v7 07/11] configs: k1: enable SD and eMMC support

Enable high-speed MMC modes.

Signed-off-by: Eric Chung <[email protected]>

---
v7:
- Remove mmc driver from MAINTAINERS file.
v5:
- Remove ADMA support since it depends on CMD23 support.
- Enable PINCONF support for related power source setting.
v2:
- Enable ADMA support.
- Enable SYSCON support.
---
 configs/spacemit_k1_defconfig | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/configs/spacemit_k1_defconfig b/configs/spacemit_k1_defconfig
index 0604c2feefc1..c0ee3a29f233 100644
--- a/configs/spacemit_k1_defconfig
+++ b/configs/spacemit_k1_defconfig
@@ -23,6 +23,7 @@ CONFIG_DEBUG_UART_BASE=0xd4017000
 CONFIG_DEBUG_UART_CLOCK=14700000
 CONFIG_TARGET_SPACEMIT_K1=y
 CONFIG_ARCH_RV64I=y
+CONFIG_RISCV_ISA_ZICBOM=y
 CONFIG_RISCV_SMODE=y
 CONFIG_SPL_RISCV_MMODE=y
 # CONFIG_SPL_SMP is not set
@@ -48,6 +49,7 @@ CONFIG_SPL_CMD_TLV_EEPROM=y
 CONFIG_OF_UPSTREAM=y
 CONFIG_ENV_OVERWRITE=y
 CONFIG_SPL_REGMAP=y
+CONFIG_SYSCON=y
 CONFIG_SPL_SYSCON=y
 CONFIG_CLK=y
 CONFIG_CLK_CCF=y
@@ -61,6 +63,7 @@ CONFIG_MISC=y
 CONFIG_I2C_EEPROM=y
 CONFIG_SPL_I2C_EEPROM=y
 CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
 CONFIG_PINCTRL_SPACEMIT_K1=y
 CONFIG_GPIO=y
 CONFIG_DM_GPIO=y
@@ -87,9 +90,26 @@ CONFIG_SPI_FLASH_WINBOND=y
 CONFIG_SPI_MEM=y
 CONFIG_SYS_SPI_U_BOOT_OFFS=0x000a0000
 CONFIG_CMD_SPI=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SPACEMIT=y
+CONFIG_MMC_IO_VOLTAGE=y
+CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_MMC_HS400_SUPPORT=y
+CONFIG_MMC_HS400_ES_SUPPORT=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=0x4
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMINFO_MAP=y
+CONFIG_EFI_PARTITION=y
 CONFIG_SPL_SPI=y
 CONFIG_SPL_DM_SPI=y
 CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SPL_SPI_LOAD=y
 CONFIG_SPL_SPI_FLASH_TINY=y
 CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_SPL_MMC=y
+CONFIG_SPL_SYS_MMCSD_RAW_MODE=y

-- 
2.51.0