RE: Error in Compilation of evaluation version of ORBACUS 4.3.0

Hi All

I was able to compile successfully by putting -frtti flag.

Many Thanks!

Arun Kumar

-----Original Message-----
From: Darren Middleman [mailto:[email protected]]
Sent: Tuesday, August 30, 2005 9:23 PM
To: Arun Kumar
Cc: [email protected]
Subject: Re: [OB-Users] Error in Compilation of evaluation version of
ORBACUS 4.3.0


Hi Arun,

>
> We are trying to use the evaluation version of ORBACUS 4.3.0 and using GNU
> GCC 3.2.3 on SOLARIS 5.8/C++ language support.
>
> We are getting following errors(segmentation fault) while doing make:
>
> make[3]: Entering directory
> `/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/ob/idl/OB'
> make[3]: Nothing to be done for `all'.
> make[3]: Leaving directory
> `/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/ob/idl/OB'
> make[2]: Leaving directory
> `/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/ob/idl'
> making all in test
> make[2]: Entering directory
> `/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/ob/test'
> making all in types
> make[3]: Entering directory
> `/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/ob/test/types'
> rm -f Types.cpp Types.h
> ../../bin/idl -I../../idl --no-skeletons Types.idl
> make[3]: *** [Types.cpp] Segmentation Fault (core dumped)
> make[3]: Leaving directory
> `/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/ob/test/types'
> make[2]: *** [all] Error 1
> make[2]: Leaving directory
> `/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/ob/test'
> make[1]: *** [all] Error 1
> `/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/ob'
> make: *** [all] Error 1
>
>
> I have attached config.env file for reference.
>
> [...]
>
> AR="g++"; export AR
> ARFLAGS="-xarch=v9 -g -O3 -fPIC -shared -o"; export ARFLAGS
> CC="gcc"; export CC
> CFLAGS=""; export CFLAGS
> CPP=""; export CPP
> CPPFLAGS="-I/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval -DNDEBUG ";
> export
> CPPFLAGS
> CXX="g++"; export CXX
> CXXFLAGS="-fno-rtti -g -O3 -fPIC -Wall -Wno-format-y2k"; export CXXFLAGS
> LDFLAGS="-L/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval "; export
LDFLAGS
> LDOPTS=""; export LDOPTS
> LD_LIBRARY_PATH="/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/
> property/lib:/
> oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/event/lib:/oracle/
> arun.kumar/raj
> neet/ORBACUS/OB-4.3.0-eval/property/lib:/oracle/arun.kumar/rajneet/
> ORBACUS/OB-4.
> 3.0-eval/naming/lib:/oracle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/ob/
> lib:/ora
> cle/arun.kumar/rajneet/ORBACUS/OB-4.3.0-eval/jtc/lib:$LD_LIBRARY_PATH";
> export L
> D_LIBRARY_PATH
> LIBEXT=".so"; export LIBEXT
> LIBPATH=""; export LIBPATH
> LIBVERFLAG="-Wl,-h,"; export LIBVERFLAG
> RANLIB=":"; export RANLIB
> RUNCONFIG="yes"; export RUNCONFIG
> TMPL_REPOS_DIR=""; export TMPL_REPOS_DIR

I just had a look again at the config.env file you sent and I see that you
are using the flag -fno-rtti.  Orbacus requires that RTTI is enabled to
allow dynamic casts to work properly.  I would suggest removing that flag
and rebuilding Orbacus to see if that clears up the segmentation fault.

Regards,
Darren

--
Darren Middleman, Software Engineer
Team Orbacus - Your CORBA Source
Email: mailto:[email protected]
WWW: http://www.orbacus.com/

_______________________________________________
OB-Users Mailing List - [email protected]
http://mail.ooc.nf.ca/mailman/listinfo/ob-users
Visit our support FAQ before you send a message.
http://www.orbacus.com/faq/support.html