RE: Compiling from editor question - return to specific line number (Toad 11.5)

Forget the second question, I found the answer (CTRL + G) but I would really hope that the answer to the first question is that such an option exists and I simply need to find/identify where it is to set!

Is there an option I can set that after compiling the code the cursor returns to the last position it was in?


[cid:[email protected]]

Joseph E. Meyers I<http://josephmeyers.com/>
Banner Functional Support Specialist
Adjunct Lecturer
Cayuga Community College
197 Franklin Street T331
Auburn, NY 13021
AIM<http://aim.com/>/EMAIL: [email protected]<mailto:[email protected]>
(phone) 315-255-1792 x2270
Think Big. Start Smart.



01001010 01101111 01110011 01100101 01110000 01101000 00100000 01000101 00101110 00100000 01001101 01100101 01111001 01100101 01110010 01110011 00100000 01001001

0101011101101000011110010010000001110111011011110111010101101100011001000010000001100001011011100111100101101111011011100110010100100000011101110110000101101110011101000010000001110100011011110010000001101010011101010110110101110000001000000110111101110101011101000010000001101111011001100010000001100001001000000111000001100101011100100110011001100101011000110111010001101100011110010010000001100111011011110110111101100100001000000110000101101001011100100111000001101100011000010110111001100101001111110000110100001010000011010000101001000010011001010110001101100001011101010111001101100101001000000111010001101000011001010010000001100100011011110110111101110010001000000111011101100001011100110010000001101111011100000110010101101110001000010010000100001101000010100000110100001010010000100110110001110101011001010010000001010011011010110110100101100101011100110010000100100001

From: [email protected] [mailto:[email protected]] On Behalf Of Joseph E Meyers I
Sent: Friday, August 10, 2012 10:21 AM
To: [email protected]
Subject: [toad] Compiling from editor question - return to specific line number (Toad 11.5)



[cid:[email protected]]
When you compile code from the editor window the cursor scrolls through all of the code and ends up at the bottom of the code.

For very short scripts this is fine, but when your code is thousands of lines long and you make a change in the middle, compile and find your cursor at the bottom it becomes tedious to try and recall where in the code you were last.

Is there an option I can set that after compiling the code the cursor returns to the last position it was in?

Is there an option/shortcut to bring up an ability to enter a line number to go directly to?



[cid:[email protected]]

Joseph E. Meyers I<http://josephmeyers.com/>
Banner Functional Support Specialist
Adjunct Lecturer
Cayuga Community College
197 Franklin Street T331
Auburn, NY 13021
AIM<http://aim.com/>/EMAIL: [email protected]<mailto:[email protected]>
(phone) 315-255-1792 x2270
Think Big. Start Smart.



01001010 01101111 01110011 01100101 01110000 01101000 00100000 01000101 00101110 00100000 01001101 01100101 01111001 01100101 01110010 01110011 00100000 01001001

01010111011010000111100100100000011101110110111101110101011011000110010000100000011000010110111001111001011011110110111001100101001000000111011101100001011011100111010000100000011101000110111100100000011010100111010101101101011100000010000001101111011101010111010000100000011 01111011001100010000001100001001000000111000001100101011100100110011001100101011000110111010001101100011110010010000001100111011011110110111101100100001000000110000101101001011100100111000001101100011000010110111001100101001111110000110100001010000011010000101001000010011001010110001101100001011101010111001101100101001000000111010001101000011001010010000001100100011011110110111101110010001000000111011101100001011100110010000001101111011100000110010101101110001000010010000100001101000010100000110100001010010000100110110001110101011001010010000001010011011010110110100101100101011100110010000100100001