Re: Where do I add my peripherals?

Hi, it's me again. I'm trying to add a define macro to the configure
script, and even though I have well created the ./configure --help output
(modifiying configure.in), I can't get it on my config.h .

Any ideas?
Thank a lot in advance

2016-07-11 11:28 GMT+02:00 Javier Fileiv <[email protected]>:

> Regarding to the device model, I'm looking for the precise moment where,
> for example, an address is put on the bus to read/write on some
> devices/memory. Because is there were I need to interface it with my target
> devices I already have model-ed.
>
> Would you be able to help me with that or should I ask Volker?
>
> 2016-07-11 10:29 GMT+02:00 Javier Fileiv <[email protected]>:
>
>> Thank you very much Stanislav!
>>
>> 2016-07-11 10:26 GMT+02:00 Stanislav Shwartsman <[email protected]>:
>>
>>> If you complied with CPU level=6 you could configure Pentium through RC
>>> file (look cpu model option).
>>> For 486 you need to recompile with CPU level=4.
>>>
>>>
>>>
>>> On Mon, Jul 11, 2016 at 11:24 AM, Javier Fileiv <[email protected]
>>> > wrote:
>>>
>>>> Hi, thanks for your reply!
>>>>
>>>> I had enable cpu level = 6, but how to launch in 486, and in pentium
>>>> mode only changing some parameter on the rc file? I would like to launch
>>>> different machines without needing to re compile it. Is that possible?
>>>> Because what you just said needs a new building and I would like to be able
>>>> to launch different machine types with only one building.
>>>>
>>>> How can I contact Volker?
>>>>
>>>> Thanks a lot for your advice
>>>>
>>>>
>>>> 2016-07-11 6:20 GMT+02:00 Stanislav <[email protected]>:
>>>>
>>>>> Ø  is it possible with only one compilation and different rc files,
>>>>> launch bochs in 486 and pentium emulation?
>>>>>
>>>>>
>>>>>
>>>>> Of course it is, this is “default” mode.
>>>>>
>>>>> When compiling --enable-cpu-level=5 you get Pentium (with or without
>>>>> MMX)
>>>>>
>>>>> When compiling --enable-cpu-level=4 you get 486
>>>>>
>>>>>
>>>>>
>>>>> Ø  I was able to find out where the rc config file is being processed
>>>>> but I can't find where does it instantiate all the hardware peripheral
>>>>> (e.g. PIC, PCI, RAM, etc)
>>>>>
>>>>> All is done through config.cc and paramtree. You need to ask Volker
>>>>> for more details.
>>>>>
>>>>>
>>>>>
>>>>> *From:* Javier Fileiv [mailto:[email protected]]
>>>>> *Sent:* Friday, July 08, 2016 11:06 AM
>>>>> *To:* [email protected]
>>>>> *Subject:* [Bochs-developers] Where do I add my peripherals?
>>>>>
>>>>>
>>>>>
>>>>> Hello everyone, I need to modify bochs source code in order to add
>>>>> some peripheral to match it with my targer board.
>>>>>
>>>>> I was able to find out where the rc config file is being processed but
>>>>> I can't find where does it instantiate all the hardware peripheral (e.g.
>>>>> PIC, PCI, RAM, etc)
>>>>>
>>>>> Also I would like to know... is it possible with only one compilation
>>>>> and different rc files, launch bochs in 486 and pentium emulation?
>>>>>
>>>>> Thank you all
>>>>>
>>>>> BR
>>>>>
>>>>
>>>>
>>>
>>
>

------------------------------------------------------------------------------
What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic
patterns at an interface-level. Reveals which users, apps, and protocols are 
consuming the most bandwidth. Provides multi-vendor support for NetFlow, 
J-Flow, sFlow and other flows. Make informed decisions using capacity planning
reports.http://sdm.link/zohodev2dev

_______________________________________________
bochs-developers mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bochs-developers