| Newsgroups |
gmane.comp.emulators.hercules390.general |
| Message-ID |
<[email protected]> |
I've got exactly same issue. I've been playing around for days to try to get it to work.
Looks from your config file like you're host machine is using Linux. I'm using Windows, and one thing I've found is that generic.prm statements all need to be on line 1.
I'm trying with LCS and CTC devices for networking......relevant drivers get loaded.
The 3 DASD are detected fine:
2019/06/05 22:23:41.981 00002300 124.922322! lcs: Loading LCS driver
2019/06/05 22:23:41.981 00002300 124.996407! ctcm: CTCM driver initialized
2019/06/05 22:23:42.211 00002300 125.152868! dasd-eckd 0.0.0121: New DASD 3390/0C (CU 3990/02) with 10017 cyli
2019/06/05 22:23:42.211 00002300 nders, 15 heads, 224 sectors
2019/06/05 22:23:42.211 00002300 125.153055! dasd-eckd 0.0.0120: New DASD 3390/0C (CU 3990/02) with 10017 cyli
2019/06/05 22:23:42.211 00002300 nders, 15 heads, 224 sectors
2019/06/05 22:23:42.211 00002300 125.174246! dasd-eckd 0.0.0122: New DASD 3390/0C (CU 3990/02) with 10017 cyli
2019/06/05 22:23:42.211 00002300 nders, 15 heads, 224 sectors
2019/06/05 22:23:42.510 00002300 125.454616! net ctc0: setup OK : r/w = ch-0.0.0560/ch-0.0.0561, protocol : 0
I've tried pointing root to different locations
e.g. root=/dev/ram0
I've turned on rd.debug, but don't see any additional clues.
Here's the debug immediately before the issue:
2019/06/05 22:35:54.216 00002CEC /lib/dracut-lib.sh@418(source_all): for f in '"/$_dir"/*.sh'
2019/06/05 22:35:54.216 00002CEC /lib/dracut-lib.sh@418(source_all): ' ' -e '//lib/dracut/hooks/emergency/80-\x2f
2019/06/05 22:35:54.216 00002CEC dev\x2froot.sh' '!'
2019/06/05 22:35:54.216 00002CEC /lib/dracut-lib.sh@418(source_all): . '//lib/dracut/hooks/emergency/80-\x2fdev\x
2019/06/05 22:35:54.216 00002CEC 2froot.sh'
2019/06/05 22:35:54.216 00002CEC ///lib/dracut/hooks/emergency/80-\x2fdev\x2froot.sh@1(source): ' ' -e /dev/root
2019/06/05 22:35:54.216 00002CEC '!'
2019/06/05 22:35:54.216 00002CEC ///lib/dracut/hooks/emergency/80-\x2fdev\x2froot.sh@1(source): warn '/dev/root d
2019/06/05 22:35:54.216 00002CEC oes not exist'
2019/06/05 22:35:54.216 00002CEC //lib/dracut-lib.sh@67(warn): echo 'Warning: /dev/root does not exist'
2019/06/05 22:35:54.216 00002CEC Warning: /dev/root does not exist
Here's my current generic.prm (it's changing every 5 minutes as I try all kinds of things).
One thing I'm not sure about is the "ip=" parameter. The gateway IP address, 192.168.1.72, is my host PC IP address. Not sure if that should be something else though. I've tried the gateway IP address my Windows PC uses, 192.168.1.254, doesn't make any difference.
rd.debug ip=192.168.1.151::192.168.1.72:24:foobar.systemz.example.com::none rd.dasd=0.0.0120 rd.dasd=0.0.0120 rd.dasd=0.0.0121 rd.dasd=0.0.0122 inst.repo=http://192.168.1.72/ inst.text inst.stage2=http://192.168.1.72/images/install.img ro ramdisk_size=40000 cio_ignore=all,!condev