| Newsgroups |
gmane.comp.emulators.hercules390.general |
| Message-ID |
<[email protected]> |
---In [email protected], <winkelmann@...> wrote :
> If things are working with script, config file, Hercules
> and MVS from TK4-, but not when using your config
> file and script, then this is clearly not a TK4- issue,
> but a problem with your script and/or config file.
Or it is an intermittent fault.
> You cannot expect anybody to name a config file
> option that would fix that, without at least providing
> the config file and the script _in full_.
I have now stripped away my mods and
this is the only modification I have now:
C:\mvs380>diff -w mvs.bat startmvs2.bat
17c17
< SET DAEMON=-d
---
> rem SET DAEMON=-d
So I run startmvs2 and wait for the scripts to
complete, and then type "quit". The first time
I did this with the untouched TK4- it actually
worked, ie all the verbiage was displayed on
the screen and the log, like this:
04:25:04 HHC01413I Hercules version 4.00
04:25:04 HHC01414I (c) Copyright 1999-2012 by Roger Bowler, Jan Jaeger, and others
04:25:04 HHC01415I Built on Jun 26 2016 at 22:04:26
...
04:26:51 HHC00338I 0:0180 dasd/work02.180
04:26:51 HHC00339I 0:0180 [0] 0000090846 000% 0000 rw 0000003 0000000 0000001
04:26:51 HHC01465I 0:0180 device detached
04:26:51 HHC00333I 0:0190 size free nbr st reads writes l2reads hits switches
04:26:51 HHC00335I 0:0190 --------------------------------------------------------------------
04:26:51 HHC00336I 0:0190 [*] 0049477921 002% 0025 0000003 0000000 0000001 0000000 0000003
04:26:51 HHC00338I 0:0190 dasd/work03.190
04:26:51 HHC00339I 0:0190 [0] 0049477921 002% 0025 rw 0000003 0000000 0000001
04:26:51 HHC00101I Thread id 00002BE8, prio 0, name Read-ahead thread-1 ended
04:26:51 HHC00101I Thread id 00004FC0, prio 0, name Read-ahead thread-2 ended
04:26:51 HHC00101I Thread id 000035AC, prio 0, name Garbage collector ended
04:26:51 HHC00101I Thread id 000026FC, prio 0, name Writer thread-1 ended
04:26:51 HHC00101I Thread id 00005354, prio 0, name Writer thread-2 ended
04:26:51 HHC01465I 0:0190 device detached
04:26:51 HHC01427I Main storage released
04:26:51 HHC01427I Expanded storage released
04:26:51 HHC01422I Configuration released
04:26:51 HHC01424I All termination routines complete
04:26:51 HHC02103I Logger: logger thread terminating
But the second time I ran it, the log ended like this:
04:34:05 HHC01603I quit
04:34:05 HHC01420I Begin Hercules shutdown
04:34:05 HHC01423I Calling termination routines
04:34:05 HHC00101I Thread id 00003D9C, prio 0, name Hercules Automatic Operator ended
04:34:05 HHC00101I Thread id 00003D10, prio -20, name Timer ended
04:34:05 HHC02272I Highest observed MIPS and IO/s rates
04:34:05 HHC02272I from Sat Jun 22 00:00:00 2019
04:34:05 HHC02272I to Sat Jun 22 04:34:05 2019
04:34:05 HHC02272I MIPS: 11.604206 IO/s: 1019
04:34:05 HHC00101I Thread id 0000350C, prio 0, name Socket device listener ended
04:34:05 HHC00101I Thread id 00001168, prio 0, name HTTP server ended
04:34:05 HHC00101I Thread id 000022B8, prio 15, name Processor CP00 ended
04:34:05 HHC01465I 0:0002 device detached
04:34:05 HHC01465I 0:000E device detached
04:34:05 HHC01465I 0:000C device detached
04:34:05 HHC01465I 0:000D device detached
04:34:05 HHC01465I 0:0480 device detached
04:34:05 HHC01465I 0:010C device detached
04:34:05 HHC01465I 0:010D device detached
04:34:05 HHC01465I 0:000F device detached
04:34:05 HHC01465I 0:030E device detached
04:34:05 HHC01465I 0:0009 device detached
04:34:05 HHC01465I 0:00C0 device detached
04:34:05 HHC01465I 0:00C1 device detached
04:34:05 HHC01465I 0:00C2 device detached
04:34:05 HHC01465I 0:00C3 device detached
04:34:05 HHC01465I 0:00C4 device detached
04:34:05 HHC01465I 0:00C5 device detached
04:34:05 HHC01465I 0:00C6 device detached
04:34:05 HHC01465I 0:00C7 device detached
So it is a timing-sensitive problem.
You may be able to reproduce the problem if
you switch off daemon mode, use "quit" after
the IPL is fully complete, and check the end
of the log file, and do this process multiple times.
BFN. Paul.