| Newsgroups |
gmane.comp.emulators.hercules390.general |
| Message-ID |
<[email protected]> |
And further progress - it helps when you spell LEGACYSENSEID correctly in
the config file.
Printers and tapes are sorted, sorry for the noise.
Peter
> -----Original Message-----
> From: [email protected] <[email protected]>
> Sent: Sunday, February 16, 2020 9:25 PM
> To: '[email protected]' <[email protected]>
> Subject: RE: [hercules-390] RE: Does Herc support DIAG 540?
>
> Further progress -- Apparently VM/ESA does not like a full 2G main storage
size.
> 2047M seems to work and it boots to the OPERATOR on the console.
>
> Next issue is that it does not know what the printers and tape drives are.
I have
> pasted messages from the Hercules log and the OPERATOR console below.
>
> I tried changing the printers 00E and 00F to 3211 devices with no
difference. I
> also added LEGASYSENSEID ENABLE to the Hercules configuration with no
> change in the results for 00E/F and the tapes 580/1.
>
> Again, TIA for any help you can provide.
>
> Peter
>
> Hercules messages:
>
> 16:32:17 HHC01315I 0:000C CHAN: ccw E4200100 7F45F06E
> 16:32:17 HHC01312I 0:000C CHAN: stat 0E00, count 0000=>40100000 F2F4F0D9
> C5E2F000 00000005 ...240RES0.....
> 16:32:17 HHC01313I 0:000C CHAN: sense 80000000 00000000 00000000
> 00000000 00000000 00000000 00000000 00000000
> 16:32:17 HHC01315I 0:000E CHAN: ccw E4200100 7F47806E
> 16:32:17 HHC01315I 0:000F CHAN: ccw E4200100 7F46206E
> 16:32:17 HHC01312I 0:000E CHAN: stat 0E00, count 0000=>00000000 00000000
> 00000000 00000000 ................
> 16:32:17 HHC01312I 0:000F CHAN: stat 0E00, count 0000=>FF350501 35250100
> 00000000 00000000 ................
> 16:32:17 HHC01314I 0:000C CHAN: sense CMDREJ
> 16:32:17 HHC01313I 0:000E CHAN: sense 80000000 00000000 00000000
> 00000000 00000000 00000000 00000000 00000000
> 16:32:17 HHC01314I 0:000E CHAN: sense CMDREJ
> 16:32:17 HHC01313I 0:000F CHAN: sense 80000000 00000000 00000000
> 00000000 00000000 00000000 00000000 00000000
> 16:32:17 HHC01314I 0:000F CHAN: sense CMDREJ
> 16:32:17 HHC01315I 0:0580 CHAN: ccw E4200100 7F45F06E
> 16:32:17 HHC01315I 0:0581 CHAN: ccw E4200100 7F46306E
> 16:32:17 HHC01312I 0:0581 CHAN: stat 0200, count 0000=>E5D6D3F1 F2F4F0E2
> D7D3F000 00000005 VOL1240SPL0.....
> 16:32:17 HHC01313I 0:0581 CHAN: sense C0220000 01C00300 00000000
> 00800100 010000FF FF000000 00000000 00000000
> 16:32:17 HHC01314I 0:0581 CHAN: sense CMDREJ INTREQ EOC WRI
> 16:32:17 HHC01312I 0:0580 CHAN: stat 0200, count 0000=>40220000 00C00300
> 00000000 00800100 ....{..........
> 16:32:17 HHC01313I 0:0580 CHAN: sense C0220000 01C00300 00000000
> 00800100 010000FF FF000000 00000000 00000000
> 16:32:17 HHC01314I 0:0580 CHAN: sense CMDREJ INTREQ EOC WRI
>
> OPERATOR CONSOLE messages, note the one where it cannot identify the 00E
> device at all.
>
> 21:22:33 FILES: NO RDR, NO PRT, NO PUN
> 21:22:33 LOGON AT 21:22:33 EST SUNDAY 02/16/20
> 21:22:33 GRAF 0200 LOGON AS OPERATOR USERS = 1
> 21:22:33 HCPIIO6785E Unable to identify device 000E dynamically.
> 21:22:33 HCPIOP952I 2047M system storage
> 21:22:33 FILES: 0000002 RDR, 0000001 PRT, NO PUN
> 21:22:33 RDR 000C STARTED SYSTEM
>
> > -----Original Message-----
> > From: [email protected] <[email protected]>
> > Sent: Sunday, February 16, 2020 3:22 PM
> > To: '[email protected]' <[email protected]>
> > Subject: RE: [hercules-390] RE: Does Herc support DIAG 540?
> >
> > Ivan,
> >
> > I tried changing the CPUMODEL to 3135 as you did but I still get that
> > DIAG 540 error and the 3270 console at device 200 still does not
> > respond when Enter or Clear is pressed.
> >
> > Would you please share your Hercules config file that worked so I can
> > see what I have done wrong?
> >
> > TIA for your help.
> >
> > Peter
> >
> > > -----Original Message-----
> > > From: [email protected] <[email protected]>
> > > Sent: Sunday, February 16, 2020 11:43 AM
> > > To: [email protected]
> > > Subject: Re: [hercules-390] RE: Does Herc support DIAG 540?
> > >
> > >
> > > On 2/16/2020 5:33 PM, Ivan Warren [email protected] [hercules-390]
> wrote:
> > > > On 2/16/2020 4:28 PM, [email protected] [hercules-390] wrote:
> > > >> After I sent this I noticed that this Yahoo group says that it
> > > >> doesn't allow attachments, so I am pasting the config and log files
here.
> > > >>
> > > >> Main config file first, included DASD config second, log last.
> > > >>
> > > >> Peter
> > > >>
> > > >> vmesaSD3X.cnf:
> > > >>
> > > >> ARCHMODE ESA/390
> > > >> CNSLPORT 3270
> > > >> CPUMODEL 9672
> > > >> CPUSERIAL 012345
> > > > Try setting a different CPU model.. VM has a bad habit of trying
> > > > to do crazy stuff when running into specific CPU models.
> > > >
> > > > --Ivan
> > > >
> > > I've Tried IPLing (for a test) VM/ESA on hercules being declared as
> > > a
> > > 3135 (Yes.. a *magical* S/370 135 with 2GB of memory with XA
> > > support) and VM/ESA was happy with it ! But When I told it it was a
> > > 3090 it tried issuing weird SERVC calls we couldn't understand and
> > > it went kaboom ! So maybe the 9672 (Is that an 9021/9121/9221 or a
> > > Multiprise... has some special call we don't handle).
> > >
> > > --Ivan