RE: IND$FILE

Hi Mike:

 

Let me tell you a little bit about the environment I have.

 

I am running:

*         Windows XP SP3

*         Herc GUI 1.8.15 4316

*         Hercules 3.07

*         Submitting via SPF/PRO to the Hercules reader

*         Using CryptoTerm for TN3270

 

I used Xmit Manager to extract the files from the Xmit file.

 

When I get the messages:

 

12.30.52 JOB   14  IEC502E R 480,      ,NL,LOADTAPE,IND$FILE
12.30.52 JOB   14 *IEC501A M 480,INDFIL,SL,6250 BPI,LOADTAPE,IND$FILE

 

I already had mounted the tape with the Herc GUI and the system dismounts it
and asks for a mount again, this can go on forever or until I cancel the
Job.

 

In the message IEC502E R 480,      ,NL,LOADTAPE,IND$FILE

 

R - Implies RETAIN volume; the volume is to be demounted and retained near
the system for future use. In the event that the job ends and the volume has
not been remounted, the operator must determine what disposition to give to
the volume. This message will appear if a volume is rejected because it is
not the volume requested (for example, a conflict in the label, label type,
or density).  This according to the System Messages Manual.   

 

In this case the system notes NL for an unlabeled tape.

 

Is there anything else I should be doing?

 

 

 

 

Carlos Aguilera

1401 Liggates Rd

Lynchburg VA 24502

Carlos-FiVMtmHp2a9Wk0Htik3J/[email protected]

434-401-4828

 

 

-----Original Message-----
From: [email protected] [mailto:[email protected]] On
Behalf Of Mike Rayborn
Sent: Monday, May 17, 2010 6:14 PM
To: [email protected]
Subject: Re: [turnkey-mvs] IND$FILE

 

Carlos, it's been a long while since I've played with any of this so 

bare with me.

 

The tape file is in fact a SL tape with volser=INDFIL.

 

When you run your job and it gets to that point with the IEC501A 

message, it's asking you to mount the INDFIL volser on device 480. My 

guess would be that you don't have the tape file mounted on device 480 ?

 

I think you may need to do a:

MOUNT 480,VOL=(SL,INDFIL),USE=PRIVATE

 

Anyway, good luck. Many others have installed IND$FILE from the files 

section. You may need to ask someone with a bit more operator experience .

 

--Mike Rayborn

 

On 5/17/2010 1:51 PM, [email protected] wrote:

> 

> I know this is not a new issue but I am running into the same wall as 

> others before me.

> I am trying to install IND$FILE and I get this messages when I run the 

> JCL out of the box:

> //LOADTAPE JOB (JCLLIB),

> // 'LOADTAPE',

> // CLASS=A,NOTIFY=HERC01,

> //* MSGCLASS=A,

> // MSGLEVEL=(0,0)

> //IND$FILE EXEC PGM=IEBCOPY

> //SYSPRINT DD SYSOUT=*

> //SYSUT3 DD UNIT=SYSDA,SPACE=(TRK,(1,1))

> //SYSUT4 DD UNIT=SYSDA,SPACE=(TRK,(1,1))

> //TAPE DD DSN=IND$FILE.LOAD,

> // UNIT=TAPE,

> // LABEL=(1,SL,,,EXPDT=98000),

> // VOL=(,RETAIN,,,SER=INDFIL),

> // DISP=(OLD,PASS)

> //DISK DD DSN=SYS2.CMDLIB,DISP=SHR

> //SYSIN DD *

> COPY INDD=TAPE,OUTDD=DISK

> SELECT MEMBER=((IND$FILE,,R),CODEPAGE,CDPG1047,CDPG037)

> /*

> //DBSTOP EXEC DBSTOP

> //DBSTART EXEC DBSTART

> the message reads:

> 12.30.52 JOB 14 IEC502E R 480, ,NL,LOADTAPE,IND$FILE

> 12.30.52 JOB 14 *IEC501A M 480,INDFIL,SL,6250 BPI,LOADTAPE,IND$FILE

> It tells me that the tape file is unlabeled

> When I change it to:

> // LABEL=(1,NL,,,EXPDT=98000),

> I get these other messages:

> 12.52.02 JOB 20 IEF403I LOADTAPE - STARTED - TIME=12.52.02

> 12.52.02 JOB 20 *IEF233A M 481,INDFIL,,LOADTAPE,IND$FILE

> 12.52.46 JOB 20 IEA000I 481,EQC,3F,0E00,,,INDFIL,LOADTAPE,12.52.46

> 12.52.46 JOB 20 IEA000I 

> 481,,,,1020000000C003600000000000800100010000FFFF000000,0000

> 12.52.46 JOB 20 IEC210I 

> 214-08,IFG0202F,LOADTAPE,IND$FILE,TAPE,481,INDFIL,IND$FILE.LOAD

> 12.52.46 JOB 20 IEF450I LOADTAPE IND$FILE - ABEND S214 U0000 - 

> TIME=12.52.46

> 12.52.46 JOB 20 IEFACTRT - Stepname Procstep Program Retcode

> 12.52.46 JOB 20 LOADTAPE IND$FILE IEBCOPY AB S214

> I also have tried bypassing label process and does not work either.

> Any hints??????

> Carlos Aguilera

> 

> 

 

 

------------------------------------

 

Yahoo! Groups Links

 

    http://groups.yahoo.com/group/turnkey-mvs/

 

    Individual Email | Traditional

 

    http://groups.yahoo.com/group/turnkey-mvs/join

    (Yahoo! ID required)

 

    [email protected] 

    [email protected]

 

    [email protected]

 

    http://docs.yahoo.com/info/terms/