RE: Almost successfull compiling GCJ, however..

I am configuring in an empty directory.  What I mean to say

is that gen-fib is in the source directory, having gone download_prerequisites

inside the source directory.

So is there any further idea why obj/gmp/fib_table.h is blank,

and my make doesn't seem to want to finish?

[and by the way, do I still have to use --with-gmp=, --with-mpfr=, with-mpc==
 if download_prerequisites have put them all in sub directories inside
the source code directory anyway?]



> Date: Wed, 7 Mar 2012 01:20:26 +0000
> Subject: Re: Almost successfull compiling GCJ, however..
> From: [email protected]
> To: [email protected]
> CC: [email protected]; [email protected]
> 
> On 7 March 2012 00:28, Me Myself and I wrote:
> >
> > I have already done this process.  I find that gen-fib is indeed there before I start
> > either my configure or make.
> 
> That's impossible if you're configuring in an empty directory.  Why
> aren't you configuring in an empty directory as I suggested in
> previous mails?
> 
> Remove gen-fib and run 'make' again. See if it is created correctly.


> From: [email protected]
> To: [email protected]
> CC: [email protected]; [email protected]
> Subject: Re: Almost successfull compiling GCJ, however..
> Date: Tue, 6 Mar 2012 06:58:20 -0800
> 
> Me Myself and I <[email protected]> writes:
> 
> > obj/gmp/fib_table.h
> >
> > is an empty file.
> >
> > ?
> 
> That is not good.  fib_table.h is a generated file.  It is built at
> runtime by the gen-fib program.  Try simply removing fib_table.h, and
> see if it gets rebuilt correctly.  If not, look at the commands that
> make shows.  You should see it running gen-fib.  You will need to figure
> out why gen-fib is not outputing anything.
> 
> Ian
> 
> 
> >> Date: Mon, 5 Mar 2012 09:25:47 +0000
> >> From: [email protected]
> >> To: [email protected]
> >> Subject: Re: Almost successfull compiling GCJ, however..
> >> 
> >> On 03/05/2012 05:10 AM, Me Myself and I wrote:
> >> > 
> >> > In response to the previous email to self, I have altered the prefix to be
> >> > 
> >> > --prefix=/home/User/
> >> > 
> >> > and encounter the precise same sort of error:
> >> > 
> >> > make;
> >> > 
> >> > fib2_ui.c:76:29: error: 'FIB_TABLE_LIMIT' undeclared (first use in this function)
> >> > fib2_ui.c:76:29: note: each undeclared identifier is reported only once for each function it appears in
> >> > make[5] *** [fib2_ui.lo] Error 1
> >> > make[5] Leaving directory '/home/User/gcc-4.6.2/objdir/gmp/mpn'
> >> > make[4] ***all-recursive] Error 1
> >> > make[4] Leaving directory '/home/User/gcc-4.6.2/objdir/gmp'
> >> > make[3] *** [all] Error 2
> >> > make[3] Leaving directory '/home/User/gcc-4.6.2/objdir/gmp'
> >> > make[2] *** [all-stage1-gmp] Error 2
> >> > make[2] Leaving directory '/home/User/gcc-4.6.2/objdir'
> >> > make[1] *** [stage1-bubble] Error 2
> >> > make[1] Leaving directory '/home/User/gcc-4.6.2/objdir'
> >> > make: *** [all] Error 2
> >> > 
> >> > Why on earth doesn't this complete without these errors?  Can I afford to ignore them
> >> > and go on to make install; anyway?
> >> 
> >> It's hard for us to understand why you haven't looked to see
> >> what the problem is.  FIB_TABLE_LIMIT should be defined in
> >> obj/gmp/fib_table.h.
> >> 
> >> Andrew.
> >