☺ Buildbot (Sourceware): gcc - build successful (master)
builder--- via Gcc-testresults <[email protected]>
| Newsgroups | gmane.comp.gcc.test-results |
|---|---|
| Message-ID | <[email protected]> |
A restored build has been detected on builder gcc-full-debian-arm64 while building gcc.
Full details are available at:
https://builder.sourceware.org/buildbot/#/builders/311/builds/3266
Build state: build successful
Revision: a800630087b679ab4658bbaed2b3828d67b19e7e
Worker: osuosl-debian-arm64
Build Reason: (unknown)
Blamelist: Aldy Hernandez <[email protected]>, Alexandre Oliva <[email protected]>, Andrea Pinski <[email protected]>, Avinash Jayakar <[email protected]>, GCC Administrator <[email protected]>, Gerald Pfeifer <[email protected]>, Pan Li <[email protected]>
Steps:
- 0: worker_preparation ( success )
- 1: git checkout ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/1/logs/stdio
- 2: rm -rf gcc-build ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/2/logs/stdio
- 3: configure ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/3/logs/stdio
- config.log: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/3/logs/config_log
- 4: make ( warnings )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/4/logs/stdio
- warnings (233): https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/4/logs/warnings__233_
- 5: make check ( warnings )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/5/logs/stdio
- warnings (3): https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/5/logs/warnings__3_
- 6: contrib/test_summary ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/6/logs/stdio
- 7: prep ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/7/logs/stdio
- 8: collect system versions ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/8/logs/stdio
- 9: fetch .bunsen.* ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/9/logs/stdio
- 10: build bunsen.cpio.gz ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/10/logs/stdio
- 11: fetch bunsen.cpio.gz ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/11/logs/stdio
- 12: unpack bunsen.cpio.gz ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/12/logs/stdio
- 13: pass .bunsen.source.* ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/13/logs/stdio
- 14: upload to bunsen ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/14/logs/stdio
- 15: clean up ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/15/logs/stdio
- 16: rm -rf gcc-build_1 ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/311/builds/3266/steps/16/logs/stdio