☠ Buildbot (Sourceware): binutils-gdb - failed test (failure) (master)

A new failure has been detected on builder binutils-fedora-x86_64 while building binutils-gdb.

Full details are available at:
    https://builder.sourceware.org/buildbot/#/builders/77/builds/7595

Build state: failed test (failure)
Revision: a7202a38dd07a4c94dcb7f024e7c44b9f55147fb
Worker: sw3bb2
Build Reason: (unknown)
Blamelist: GDB Administrator <[email protected]>

Steps:

- 0: worker_preparation ( success )

- 1: git checkout ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/1/logs/stdio

- 2: rm -rf binutils-build ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/2/logs/stdio

- 3: configure ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/3/logs/stdio
        - config.log: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/3/logs/config_log

- 4: make ( warnings )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/4/logs/stdio
        - warnings (28): https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/4/logs/warnings__28_

- 5: make check ( failure )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/stdio
        - ld.sum: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/ld_sum
        - ld.log: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/ld_log
        - gas.sum: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/gas_sum
        - gas.log: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/gas_log
        - binutils.sum: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/binutils_sum
        - binutils.log: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/binutils_log
        - libsframe.sum: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/libsframe_sum
        - libsframe.log: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/libsframe_log
        - libctf.sum: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/libctf_sum
        - libctf.log: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/libctf_log
        - warnings (12): https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/5/logs/warnings__12_

- 6: prep ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/6/logs/stdio

- 7: build bunsen.cpio.gz ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/7/logs/stdio

- 8: fetch bunsen.cpio.gz ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/8/logs/stdio

- 9: unpack bunsen.cpio.gz ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/9/logs/stdio

- 10: pass .bunsen.source.* ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/10/logs/stdio

- 11: upload to bunsen ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/11/logs/stdio

- 12: clean up ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/12/logs/stdio

- 13: rm -rf binutils-build_1 ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/77/builds/7595/steps/13/logs/stdio