Re: GDB and MacOS 11.4/BigSur

Hi Simon,
   Thank you - the added details you gave me really helped, especially when I both obtained the official 10.2 source set, and followed the BuildingForDarwin <https://sourceware.org/gdb/wiki/BuildingOnDarwin> instructions for  ".configure --disable-intl”.

  I successfully built now, and off to use the test-suites

Sam

> On Jun 28, 2021, at 6:34 PM, Sam Warner <[email protected]> wrote:
> 
> Hi,
>   Shoot - my bad -  I wasn’t super careful when I grabbed the source, just pulling the latest HEAD off the git repository rather than the true release set of source.
> 
> Sam
> 
>  Ps, I did some more reading, and perhaps I skimmed over the second paragraph on BuildingForDarwin <https://sourceware.org/gdb/wiki/BuildingOnDarwin>.  The "To avoid such warnings building 7.0, configure with --disable-intl” line does change the build error.  
> 
>    1) make clean,  .configure (only), and make…. Build.withInternationalization.log
>    2) make clean,  ".configure --disable-intl”, make … Build.withoutInternationalization.log
> 
>   With both still having issues, I reflected back that I wasn’t super careful when I grabbed the source, just pulling the latest HEAD off the git repository, and when I re-obtained the source for 10.2 I was more careful.  The build is still progressing at this moment.  Which is a significantly longer duration than before.
> 
> 
> 
>> On Jun 28, 2021, at 5:29 PM, Sam Warner <[email protected] <mailto:[email protected]>> wrote:
>> 
>> Hi,
>>    I need a bit of help to speed things along.
>> 
>>    On macOS, zsh installs an SDK, which apparently is partially needed - yet - it produces build errors.  (Attached build.log, and config.with.szh.SDKs.log)
>>    Meanwhile, if I temporarily remove the SDK of zsh, then ‘./configure’ fails. (Attached config.without.szh.SDKs.log)
>> 
>>   I was about to start setting up LD and INCLUDE environment variables, yet I think this is already handled by “./configure"
>> 
>>    I’m a bit lost.  Any suggestions?
>> 
>> Sam
>> <config.without.szh.SDKs.log>
>> <config.with.szh.SDKs.log>
>> 
>> 
>>> On Jun 28, 2021, at 5:03 PM, Sam Warner <[email protected] <mailto:[email protected]>> wrote:
>>> 
>>> Never mind - found it - https://sourceware.org/gdb/wiki/Internals%20Testsuite <https://sourceware.org/gdb/wiki/Internals%20Testsuite> 
>>> 
>>>> On Jun 28, 2021, at 2:51 PM, Sam Warner <[email protected] <mailto:[email protected]>> wrote:
>>>> 
>>>> Hi,
>>>>  One more newbie question.  After building, is there a canned set of tests to make sure what I built matches what’s expected?
>>>>  (Using gcc-11 from home-brew)
>>>> 
>>>> Sam
>>>> 
>>>> 
>>>>> On Jun 27, 2021, at 5:48 PM, Simon Marchi <[email protected] <mailto:[email protected]>> wrote:
>>>>> 
>>>>> On 2021-06-27 6:44 p.m., Sam Warner wrote:
>>>>>> Hi Simon,
>>>>>> 
>>>>>>  Thanks - yes - I’ll start with that patch first.  I obtain the same call stack
>>>>>> 
>>>>>>  My next two things to learn is how to get the equivalent of the symbol-server working, and then to setup a developer-environment for GDB.  Any pointers would be great.
>>>>> 
>>>>> I don't know what symbol-server is, I can't help you with that.
>>>>> 
>>>>> To build gdb, you normally just need to run these commands at the
>>>>> top-level:
>>>>> 
>>>>> ./configure
>>>>> make all-gdb
>>>>> 
>>>>> The built gdb will be at gdb/gdb.  But there are some additional quirks
>>>>> on macOS though, so it's not as simple as that.  GDB requires libgmp, so
>>>>> you need to install that.  You need GNU make to build (the make that
>>>>> comes with macOS is not GNU make).  You can install those using Macports
>>>>> (or Brew, I guess) or by building them by hand.  You can then probably
>>>>> get by using the commands:
>>>>> 
>>>>> ./configure --disable-nls CFLAGS="-g3 -O0" CXXFLAGS="-std=gnu++17 -g3 -O0" --with-libgmp-prefix=/opt/local
>>>>> gmake
>>>>> 
>>>>> Update /opt/local to point where your libgmp is installed.  gmake refers
>>>>> to GNU make, when installed through Macports.
>>>>> 
>>>>> Simon
>>>> 
>>> 
>> 
>