Re: Gdal on slackware

Tomas Zajc wrote:
> I'm trying to compile gdal-1.3.2 from the source code found at 
> http://www.gdal.org/download.html. After running the configure script I get 
> 
>   Installation directory:    /usr/local
>   C compiler:                gcc -O2
>   C++ compiler:              g++ -O2
> 
>   LIBTOOL support:           yes
> 
>   LIBZ support:              external
>   GRASS support:             no
>   CFITSIO support:           no
>   PCRaster support:          internal
>   NETCDF support:            no
>   LIBPNG support:            external
>   LIBTIFF support:           external
>   LIBGEOTIFF support:        internal
>   LIBJPEG support:           external
>   LIBGIF support:            external
>   OGDI support:              no
>   HDF4 support:              no
>   HDF5 support:              yes
>   KAKADU support:            no
>   JASPER support:            no
>   ECW support:               no
>   MrSID support:             no
>   POSTGRESQL support:        no
>   MySQL support:             no
>   XERCES support:            no
>   ODBC support:              no
>   OCI support:               no
>   SDE support:               no
>   DODS support:              no
>   SQLite support:            no
>   DWGdirect support          no
>   PANORAMA GIS support:      no
>   GEOS support:              no
> 
>   Statically link PROJ.4:    no
> 
>   Traditional Python:        yes
>   NG SWIG Bindings:
> 
>   enable OGR building:       yes
> 
> And when I run make i get the following error:
> 
> /bin/sh /home/tomas/gdal-1.3.2/libtool --mode=compile 
> g++ -Wall  -O2   -DOGR_ENABLED -I/home/tomas/gdal-1.3.2/port  -c -o 
> cpl_vsil_unix_stdio_64.o cpl_vsil_unix_stdio_64.cpp
>  g++ -Wall -O2 -DOGR_ENABLED -I/home/tomas/gdal-1.3.2/port -c 
> cpl_vsil_unix_stdio_64.cpp  -fPIC -DPIC -o .libs/cpl_vsil_unix_stdio_64.o
>  g++ -Wall -O2 -DOGR_ENABLED -I/home/tomas/gdal-1.3.2/port -c 
> cpl_vsil_unix_stdio_64.cpp -o cpl_vsil_unix_stdio_64.o >/dev/null 2>&1
> make[1]: Leaving directory `/home/tomas/gdal-1.3.2/port'
> (cd gcore; make)
> make[1]: Entering directory `/home/tomas/gdal-1.3.2/gcore'
> make[1]: *** No targets specified and no makefile found.  Stop.
> make[1]: Leaving directory `/home/tomas/gdal-1.3.2/gcore'
> make: *** [core-target] Error 2
> 
>  Any sugestion?

Tomas,

Is there a GNUmakefile in the gdal-1.3.2/gcore directory?  I'm really not
too clear on what the port directory would build, but the gcore directory
would not.

Best regards,
-- 
---------------------------------------+--------------------------------------
I set the clouds in motion - turn up   | Frank Warmerdam, [email protected]
light and sound - activate the windows | http://pobox.com/~warmerdam
and watch the world go round - Rush    | President OSGeo, http://osgeo.org