Re: New ASUS mobo, incomplete coverage of its sensors.

On Monday 30 March 2009, Achim Theobald wrote:
>Hi Gene,
>
>Gene Heskett schrieb:
>> Greetings all;
>>
>> I put an ASUS M2N SLI Deluxe mobo in the is box last fall, with a quad
>> core AMD 9550 Phenom on it.  I can't find the cpu thermals and fans now.
>>
>> I have installed:
>> [root@coyote linux-2.6.28.9]# rpm -qa|grep gkrellm
>> gkrellm-daemon-2.3.2-1.fc10.i386
>> gkrellm-2.3.2-1.fc10.i386
>> gkrellm-weather-2.0.7-6.fc9.i386
>> gkrellm-top-2.2.11-1.fc9.i386
>>
>> When I run sensors-detect, it gets hits on 3 drivers, 2 of which are "yet
>> to be written" and only the it87 driver if functional.
>> From that scan:
>
>This is your monitoring chip.
>
>> Trying family `ITE'...                                      Yes
>> Found `ITE IT8716F Super IO Sensors'                        Success!
>>     (address 0x290, driver `it87')
>
>Support the FC sensors package this "new" IT8716 chip? Yes? ->
>Runs the sensors daemon (what's the name on FC? sensorsd or lm_sensors)?
lm_sensors
>Take as root "modprobe it87", "service sensors status" or "service lm_sensor
> status" Do you have change your /etc/sensors.conf or /etc/sensors3.conf?

[root@coyote /]# service lm_sensors status
it8716-isa-0290
Adapter: ISA adapter
VCore:       +1.14 V  (min =  +0.00 V, max =  +4.08 V)
VDDR:        +3.20 V  (min =  +0.00 V, max =  +4.08 V)
+3.3V:       +0.00 V  (min =  +0.00 V, max =  +4.08 V)   ALARM
+5V:         +4.76 V  (min =  +0.00 V, max =  +6.85 V)
+12V:       +11.46 V  (min =  +0.00 V, max = +16.32 V)
in5:         +0.00 V  (min =  +0.00 V, max =  +4.08 V)   ALARM
in6:         +0.00 V  (min =  +0.00 V, max =  +4.08 V)   ALARM
5VSB:        +4.81 V  (min =  +0.00 V, max =  +6.85 V)
VBat:        +2.94 V
CPU Fan:    3325 RPM  (min = 1997 RPM)
Case Fan:      0 RPM  (min =    0 RPM)
fan3:          0 RPM  (min =   10 RPM)  ALARM
CPU Temp:    +47.0°C  (low  =  -1.0°C, high = +127.0°C)  sensor = thermal 
diode
M/B Temp:    +38.0°C  (low  =  -5.0°C, high = +127.0°C)  sensor = thermistor
temp3:       +17.0°C  (low  =  -1.0°C, high = +127.0°C)  sensor = thermistor
cpu0_vid:   +0.613 V

But the only temp I can get is THRM, which seems to be stuck at 104F

However, I did just find an /etc/sensors3.conf.rpmnew and put it into service 
and restarted service lm_sensors, and that does give me 2 more temp readings 
now.

That is a major improvement.

Thanks for triggering my memory.  FWIW this mobo went into service with F8 
installed on it, and it was on the upgrade(not install) of F10 that all this 
went to pot.

-- 
Cheers, Gene
"There are four boxes to be used in defense of liberty:
 soap, ballot, jury, and ammo. Please use in that order."
-Ed Howdershelt (Author)
Housework can kill you if done right.
		-- Erma Bombeck



______________________________________________
Gkrellm mailing list
[email protected]
Read archives-join-leave-set RSS feed:
http://archive.lists.netservicesgroup.com
This service is provided by The Network Services Group:
http://www.netservicesgroup.com