Re: gkrellmd question
Rio <[email protected]>
| Newsgroups | gmane.comp.gnome.apps.gkrellm |
|---|---|
| Message-ID | <[email protected]> |
On Monday 11 January 2010, you wrote: > On Mon, 11 Jan 2010 06:36:16 -0500 > Rio <[email protected]> wrote: > > > I am trying gkrellmd and using a 'remote' client as my local monitor in an attempt to > > thwart this 'duplicating' effort kde appears to be doing on just the local monitor. > > however, i find when I use gkrellmd I lose the local nvidia temp monitors for my vid card > > and tesla. > > > > is gkrellmd not capable of watching those modules? > > anything special I need to do that was not in the gkrellmd.conf? > > here is my module list > > nvidia temps are monitored using the nvdia-settings command and as far as I > know the nvidia module does not report temps directly in the kernel /sys or /proc > filesystem. > > If you have the nvidia-settings command then it should be used automatically > regardless if you are running gkrellm or gkrellmd and you will see it in the config > if it detects gpus that report temps. Also run "gkrellmd -d 0x80" and look for > the nvidia-settings line. You should get the same result as running > "gkrellm -d 0x80" on the same machine. If there are differences regarding > nvidia, what are they? > the 2 modules are kernel modules it87 26936 0 hwmon_vid 3648 1 it87 and once i made the kernel with the hwmon_vid i suddenly got temps on both cards. i dont use the nvidia-settings. i ran it once in the past 2 yrs just to look at it and see what it offered. i do use nvclock to manually set the fan speeds on both cards since the mfgr defaults are just plain stupid.they go for 'quiet' at the expense of burning the card up sooner than it should. i run them at 85% in winter and 100% in summer. my take is quiet is not to be had if you want to run a powerful computer. the heat is just too much... if you want to run a 'supercomputer' on your desk you need to put up with the mini jet engine fan volume. these are my results from the above test gkrellm -d 0x80 --- GKrellM 2.3.4 --- hddtemp_daemon_read (once a minute): |/dev/sda|WDC WD7502ABYS-02A6B0|30|C||/dev/sdb|WDC WD7502ABYS-02A6B0|30|C| nvidia-settings gpus = 2 libsensors: init OK coretemp:/sys/class/hwmon/hwmon0/device coretemp@0/temp1 1 coretemp:/sys/class/hwmon/hwmon1/device coretemp@1/temp1 10001 coretemp:/sys/class/hwmon/hwmon2/device coretemp@2/temp1 20001 coretemp:/sys/class/hwmon/hwmon3/device coretemp@3/temp1 30001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in0 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in1 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in2 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in3 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in4 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in5 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in6 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in7 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in8 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/fan1 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/fan2 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/fan3 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/fan4 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/temp1 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/temp2 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/temp3 2900001 libsensors: error determining type for: it8718@290/cpu0_vid gkrellmd -d 0x80 Starting GKrellM Daemon 2.3.4 [gkrellm_connect_to: (2,1,6) 127.0.0.1:7634] hddtemp_daemon_read (once a minute): |/dev/sda|WDC WD7502ABYS-02A6B0|30|C||/dev/sdb|WDC WD7502ABYS-02A6B0|30|C| nvidia-settings gpus = 0 libsensors: init OK coretemp:/sys/class/hwmon/hwmon0/device coretemp@0/temp1 1 coretemp:/sys/class/hwmon/hwmon1/device coretemp@1/temp1 10001 coretemp:/sys/class/hwmon/hwmon2/device coretemp@2/temp1 20001 coretemp:/sys/class/hwmon/hwmon3/device coretemp@3/temp1 30001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in0 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in1 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in2 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in3 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in4 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in5 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in6 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in7 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/in8 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/fan1 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/fan2 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/fan3 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/fan4 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/temp1 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/temp2 2900001 it8718:/sys/class/hwmon/hwmon4/device it8718@290/temp3 2900001 libsensors: error determining type for: it8718@290/cpu0_vid [gkrellm_connect_to: (2,1,6) 127.0.0.1:7634] hddtemp_daemon_read (once a minute): |/dev/sda|WDC WD7502ABYS-02A6B0|30|C||/dev/sdb|WDC WD7502ABYS-02A6B0|30|C| both give errors on libsensors for cpu0_vid. i have no idea how my local gkrellm gets the vid temps but on the gtx285 it gives me board ambient and gpu temp and gpu temp on the tesla. i have verified both are accurate by comparing their readout with nvidia-settings > Bill > > ______________________________________________ > Gkrellm mailing list > [email protected] > Read archives-join-leave-set RSS feed: > http://archive.lists.netservicesgroup.com > This service is provided by The Network Services Group: > http://www.netservicesgroup.com > > -- Rio ______________________________________________ Gkrellm mailing list [email protected] Read archives-join-leave-set RSS feed: http://archive.lists.netservicesgroup.com This service is provided by The Network Services Group: http://www.netservicesgroup.com