[system-tools] Arch Linux users-admin
Link Dupont <[email protected]>
| Newsgroups | gmane.comp.gnome.ximian.setup-tool |
|---|---|
| Message-ID | <41e4e5fb041017223550a1a849__6642.95405517823$1098077746$gmane$org@mail.gmail.com> |
Hey GST hackers, Here's a first attempt at a users-admin patch. I have tested reading & writing and it seems to work okay. Obviously, this isn't a hefty patch, since Arch Linux adheres to all the standards as far as user management goes. I didn't include an archlinux.png in the patch, though I can provide one. This patch is generated off of anonymous CVS. Cheers, Link -- Peace love and penguins _______________________________________________ system-tools-list mailing list [email protected] http://mail.gnome.org/mailman/listinfo/system-tools-list
gst-users-admin-archlinux-1.patch
(application/octet-stream, 2.8 KB)
--- gnome-system-tools/backends/users-conf.in 2004-09-14 04:33:03.000000000 -0700
+++ gnome-system-tools.patched/backends/users-conf.in 2004-10-17 21:52:21.000000000 -0700
@@ -78,6 +78,7 @@
"slackware-8.0.0", "slackware-8.1", "slackware-9.0.0", "slackware-9.1.0", "slackware-10.0.0",
"freebsd-4", "freebsd-5", "freebsd-6",
"gentoo",
+ "archlinux-0.7",
"pld-1.0", "pld-1.1", "pld-1.99", "fedora-1", "fedora-2", "specifix", "vine-3.0", "vine-3.1");
$description =<<"end_of_description;";
@@ -360,6 +361,7 @@
'vine-3.0' => $rh_logindefs_defaults,
'vine-3.1' => $rh_logindefs_defaults,
'gentoo' => $gentoo_logindefs_defaults,
+ 'archlinux-0.7' => $gentoo_logindefs_defaults,
'slackware-9.1.0' => $gentoo_logindefs_defaults,
'slackware-10.0.0' => $gentoo_logindefs_defaults,
'freebsd-4' => $freebsd_logindefs_defaults,
@@ -843,7 +845,7 @@
$fname = "-f \'" . $fname . "\'";
$home_phone = "-h \'" . $home_phone . "\'";
- if ($gst_dist =~ /^debian/)
+ if ($gst_dist =~ /^debian/ || $gst_dist =~ /^archlinux/)
{
$office = "-r \'" . $office . "\'";
$office_phone = "-w \'" . $office_phone . "\'";
--- gnome-system-tools/backends/platform.pl.in 2004-10-17 22:29:00.000000000 -0700
+++ gnome-system-tools.patched/backends/platform.pl.in 2004-10-16 09:17:33.000000000 -0700
@@ -76,6 +76,7 @@
"freebsd-5" => "FreeBSD 5",
"freebsd-6" => "FreeBSD 6",
"gentoo" => "Gentoo Linux",
+ "archlinux-0.7" => "Arch Linux 0.7",
"pld-1.0" => "PLD 1.0 Ra",
"pld-1.1" => "PLD 1.1 Ra",
"pld-1.99" => "PLD 1.99 Ac-pre",
@@ -333,6 +334,23 @@
return -1;
}
+sub check_archlinux
+{
+ # We do this because Arch puts g-s-t into /opt/gnome.
+ open RELEASE, "/etc/arch-release" or return -1;
+ while (<RELEASE>)
+ {
+ chomp;
+ if (/^Arch Linux (.*) \(.*\)/)
+ {
+ close RELEASE;
+ return "archlinux-$1";
+ }
+ }
+ close RELEASE;
+ return -1;
+}
+
sub check_linuxppc
{
open RELEASE, "$gst_prefix/etc/redhat-release" or return -1;
@@ -440,7 +458,7 @@
# Red Hat check must run after Vine, Mandrake and Fedora, and Mandrake after BlackPanther
"Linux" => [ \&check_lsb, \&check_debian, \&check_caldera, \&check_suse, \&check_blackpanther, \&check_vine,
\&check_fedora, \&check_mandrake, \&check_conectiva, \&check_linuxppc, \&check_redhat, \&check_openna,
- \&check_turbolinux, \&check_slackware, \&check_gentoo, \&check_pld, \&check_specifix ],
+ \&check_turbolinux, \&check_slackware, \&check_gentoo, \&check_pld, \&check_specifix, \&check_archlinux ],
"FreeBSD" => [ \&check_freebsd ],
"SunOS" => [ \&check_solaris ]
);