RE: Placing an outgoing call on an available trunk.

Yes, you can still do outgoing calls on the same trunk group.

It will start by using 29 if it is free then 28 etc.

I do not like to much this hunting, I would prefer incrementing.

Julien

-----Original Message-----
From: Lachlan Ross [mailto:[email protected]] 
Sent: May 3, 2005 6:50 PM
To: Julien Chavanton
Cc: Bayonne Devel Mailing List
Subject: Re: [Bayonne-devel] Placing an outgoing call on an available
trunk.

Thanks Julien and to everyone who helped out on this one!
I have 30 channels on the card in my machine.
If I have in my conf:

------------------------
[trunks]
; Specify the name of additional trunk groups to load
groups =  outgoing

[outgoing-trunks]
trunks = 
0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,2
7,28,29
-----------------------

Does this mean 0-29 are dedicated to outgoing calls only?
What impact does it have on my incoming calls?
Can incoming calls still come in on truncks 0-29?
I can then write the command 'start outgoing myScript' and it will grab 
an available trunk between 0-29 right?

Thanks again.

Lachlan


Julien Chavanton wrote:

>You must define the trunk in bayonne.conf
>
>Here is an example with 10 T1's, with E1's there is 30 channels not
only
>23.
>
>Then you can write the command "start trunk1 myScript" in bayonne.ctrl
>the bayonne FIFO.
>
>
>[trunks]
>; Specify the name of additional trunk groups to load
>groups = trunk1 trunk2 trunk3 trunk4 trunk5 trunk6 trunk7 trunk8 trunk9
>trunk10
>
>[trunk1-trunks]
>trunks = 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22
>
>[trunk2-trunks]
>trunks =
>23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45
>
>[trunk3-trunks]
>trunks =
>46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68
>
>[trunk4-trunks]
>trunks =
>70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92
>
>[trunk5-trunks]
>trunks =
>93,94,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,11
2
>,113,114
>
>[trunk6-trunks]
>trunks =
>115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132
,
>133,134,135,136,137
>
>[trunk7-trunks]
>trunks =
>138,139,140,141,142,143,144,145,146,147,148,149,150,151,152,153,154,155
,
>156,157,158,159,160
>
>[trunk8-trunks]
>trunks =
>161,162,163,164,165,166,167,168,169,170,171,172,173,174,175,176,177,178
,
>179,180,181,182,183
>
>[trunk9-trunks]
>trunks =
>184,185,186,187,188,189,190,191,192,193,194,195,196,197,198,199,200,201
,
>202,203,204,205,206
>
>[trunk10-trunks]
>trunks =
>207,208,209,210,211,212,213,214,215,216,217,218,219,220,221,222,223,224
,
>225,226,227,228,229
>
>-----Original Message-----
>From: bayonne-devel-bounces+j.chavanton=oneworldinteractive.com@gnu.org
>[mailto:[email protected]
r
>g] On Behalf Of Lachlan Ross
>Sent: May 2, 2005 9:48 PM
>To: Bayonne Devel Mailing List
>Subject: [Bayonne-devel] Placing an outgoing call on an available
trunk.
>
>Hi Everyone,
>
>When using Bayonne to dial out, must you specify the trunk that the
call
>
>goes out on?
>ie:
>bayonne --control start 1 myScript
>
>This sends the call out on trunk 1.  What happens if trunk 1 already
has
>
>a call on it?
>Can you some how place an outgoing call and have it just find an 
>available trunk?
>
>Thanks for any ideas.
>
>Lachlan
>
>
>
>
>_______________________________________________
>Bayonne-devel mailing list
>[email protected]
>http://lists.gnu.org/mailman/listinfo/bayonne-devel
>  
>