Re: Can't assign diode models in batch mode

Hello all,

I think I found the problem. It looks like the first like of my
test_schematic2.sim files needs to be a comment. Sorry for the trouble.

Thanks

-Anthony

On Wed, Feb 18, 2009 at 12:20 PM, <[email protected]> wrote:

> Hello Anthony,
>
> Just tried your circuit with batch mode.
> gnucap -b test_schematic2.sim
>
> got .dat file:
>
> #           v(10)      v(20)      v(30)
>  0.         0.         0.         0.
>  0.5        0.0042244  3.549E-12  0.
>  1.         0.38735    63.702E-6  49.E-15
>  1.5        0.85995    0.25783    426.95E-9
>  2.         1.3427     0.71012    0.12644
>  2.5        1.83       1.1785     0.55651
>  3.         2.3212     1.6585     1.0208
>  3.5        2.8146     2.144      1.4964
>  4.         3.3093     2.6326     1.9778
>  4.5        3.8049     3.1232     2.4628
>  5.         4.3011     3.6153     2.9501
>
>  Seems everything worked fine.
>
>  gnucap 2008-12-23, CentOS linux.
>
>  Cheers
>  Gena.
>
> Tuesday, February 17, 2009, 11:02:09 PM, you wrote:
>
> AA> Hello everyone,
>
> AA> I hope you all are doing well. This is my first time posting. I've just
> AA> started using gnucap this past week.
>
> AA> Here is my question. I'm trying to read in a netlist and commands in
> batch
> AA> mode. I have a file that called test_schematic2.sim.
>
> AA> The file contains:
>
> AA> .model 1N414 D IS=2e-14
> AA> Vcc  1   0   5
> AA> Dx   1  10   1N414
> AA> Dy  10  20   1N414
> AA> Dz  20  30   1N414
> AA> Rd1 10   0   1k
> AA> Rd2 20   0   1k
> AA> Rd3 30   0   1k
>
> AA> .print dc v(10) v(20) v(30)
> .dc Vcc 0 5 0.5 >>eg6.dat
> AA> .end
>
> AA> I then run:
>
> >>gnucap -b test_schematic2.sim
>
> AA> I do not receive the output file eg6.dat.
>
> AA> If I go into gnucap and pull the file in as follows:
>
> gnucap>>  <test_schematic2.sim
>
> AA> I get the following message:
>
> AA> .model 1N414 D IS=2e-14
> AA> Dx: can't find model: 1N414
>
> AA> However, I can generate the model from inside of gnucap by using the
> build
> AA> command.
>
> AA> Can you tell why I cannot get gnucap to recognize the diode model
> through
> AA> the batch mode?
>
> AA> Thanks, and I hope I'm not wasting your time with something obvious.
>
> AA> -Anthony Anconetani
> AA> _______________________________________________
> AA> Help-gnucap mailing list
> AA> [email protected]
> AA> http://lists.gnu.org/mailman/listinfo/help-gnucap
>
>
>
> --
> Best regards,
>  gserdyuk                            mailto:[email protected]
>
>