Re: OZ 3.5.4.1-rc2 released

On Wed, May 03, 2006 at 09:21:04AM +0200, Marcin Juszkiewicz wrote:
> Can you provide 'dmesg' output after inserting card with orinoco
> driver uninstalled?

pccard: PCMCIA card inserted into slot 1
pcmcia: registering new device pcmcia1.0
hostap_cs: setting Vcc=33 (constant)
hostap_cs: setting Vcc=33 (from config)
Checking CFTABLE_ENTRY 0x01 (default 0x01)
IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
io->flags = 0x0046, io.base=0x0000, len=64
hostap_cs: Registered netdevice wifi0
hostap_cs: index 0x01: Vcc 3.3, irq 137, io 0xc4840000-0xc484003f
prism2_hw_init: initialized in 190 ms
wifi0: NIC: id=0x801b v1.0.0
wifi0: PRI: id=0x15 v1.1.1
wifi0: STA: id=0x1f v1.7.4
wifi0: registered netdevice wlan0
wlan0: Host AP mode does not support 'Any' essid
prism2: wlan0: operating mode changed 3 -> 2
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=33:33:00:00:00:16 A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=33:33:ff:dd:7d:a1 A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=ff:ff:ff:ff:ff:ff A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=33:33:00:00:00:02 A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=ff:ff:ff:ff:ff:ff A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=33:33:00:00:00:16 A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=ff:ff:ff:ff:ff:ff A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=33:33:00:00:00:02 A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=33:33:00:00:00:02 A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=ff:ff:ff:ff:ff:ff A4=00:00:00:00:00:00
wlan0: no IPv6 routers present
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=ff:ff:ff:ff:ff:ff A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=ff:ff:ff:ff:ff:ff A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=ff:ff:ff:ff:ff:ff A4=00:00:00:00:00:00
wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
   A1=00:00:00:00:00:00 A2=00:0c:41:dd:7d:a1 A3=ff:ff:ff:ff:ff:ff A4=00:00:00:00:00:00

> I would like to get also 'pccardctl ident' output.

Socket 0:
  product info: "HITACHI", "microdrive", "", ""
  manfid: 0x0319, 0x0000
  function: 4 (fixed disk)
Socket 1:
  product info: "Linksys", "Wireless CompactFlash Card", "", ""
  manfid: 0x028a, 0x0673
  function: 6 (network)

Hmm... there is something wrong with pccardctl too, it segfaults when
I do something besides 'ident':

    root@spitz:~# pccardctl 
    Segmentation fault

    root@spitz:~# pccardctl --help 
    Segmentation fault

When my AP goes out of reach, I get:
    eth0: New link status: AP Out of Range (0004)

And, hopefully, later:
    eth0: New link status: AP In Range (0005)

The AP is just around the corner (no direct line of sight), and the
wifi card was pointed at the AP, at a distance of 3 meters.  That
shouldn't cause an "Ap Out of Range" error IMO. "iwlist scan" gives
me:

    eth0  Scan completed :
          Cell 01 - Address: 00:11:E2:00:C4:47
                    ESSID:"heggerankweg"
                    Mode:Master
                    Frequency:2.432 GHz (Channel 5)
                    Signal level:52/153  Noise level:25/153
                    Encryption key:off
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s

I don't know about the orinoco levels - I'm used to seeing the
hostap's dBm levels, but 52 out of a possible 153 seems like a good
signal to me.

-- 
Sybren Stüvel

"Gravitation cannot be held responsible for people falling in love."
-- Albert Einstein

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2.2 (GNU/Linux)

iD8DBQFEWGECNIPvGICzDyQRAl8+AJ9Nx/jd5OW6D8VUICAQvwuuoCvNrACcDFuW
X9WnXB+edIvr435iNPldPV4=
=8UeF
-----END PGP SIGNATURE-----