stk600

Hello,

Sorry I bother you all with a -for me- confusing but probably simple problem. I am trying to use a STK600 to program a tiny85. Connecting to the device fails, see below. What should I do??

Using Mac OSX 10.7.5 with Crosspack AVR 20121207. This is from Terminal:

iibmac:~ gbosch$ avrdude -c stk600 -p t85 -P usb:7A:5B -v

avrdude: Version 5.11.1, compiled on Dec  6 2012 at 23:54:36
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "/usr/local/CrossPack-AVR-20121207/etc/avrdude.conf"
         User configuration file is "/Users/gbosch/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : usb:7A:5B
         Using Programmer              : stk600
avrdude: usbdev_open(): Found STK600, serno: 0048395C7A5B
         AVR Part                      : ATtiny85
         Chip Erase delay              : 4500 us
         PAGEL                         : P00
         BS2                           : P00
         RESET disposition             : possible i/o
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65     6     4    0 no        512    4      0  4000  4500 0xff 0xff
           flash         65     6    32    0 yes      8192   64    128  4500  4500 0xff 0xff
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00
           lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           calibration    0     0     0    0 no          2    0      0     0     0 0x00 0x00

         Programmer Type : STK600
         Description     : Atmel STK600
         Programmer Model: STK600
         Hardware Version: 3
         Firmware Version Master : 2.20
         Firmware Version Slave 1: 2.01
         Firmware Version Slave 2: 2.02
         Routing card    : STK600-RC008T-2
         Socket card     : STK600-DIP
         RC_ID table rev : 47
         EC_ID table rev : 1
         Vtarget         : 4.8 V
         Varef 0         : 1.10 V
         Varef 1         : 0.00 V
         SCK period      : 8.00 us
         Oscillator      : 16.007 MHz

avrdude: stk500v2_command(): command failed
avrdude: stk500v2_program_enable(): bad AVRISPmkII connection status: MOSI fail
avrdude: initialization failed, rc=-1
         Double check connections and try again, or use -F to override
         this check.


avrdude done.  Thank you.


Anyone who can help?
Thanks, Gerrit.