2801 router adsl wan interface card düşük hızda buluşma problemi

merabalar herkese.Hattım 4 mb adsl fakat 2801 in üzerine takılı adsl kart var.modem 832 line rate ile buluşuyor sebebini bilen var mı?Başka marka modem takınca 4mb hızı görüyorum.

interface ATM0/2/0
 no ip address
 load-interval 30
 no snmp trap link-status
 no atm ilmi-keepalive
 pvc 8/35 
  encapsulation aal5snap
  pppoe-client dial-pool-number 1
 !
!
interface Dialer0
 ip address negotiated
 ip mtu 1492
 ip virtual-reassembly
 encapsulation ppp
 ip tcp adjust-mss 1452
 load-interval 30
 dialer pool 1
 dialer-group 1
 ppp pap sent-username xxxx@xxnet password xxxx
 ppp ipcp dns request
show çıktıları
e#sh controllers atm 0/2/0
Interface: ATM0/2/0, Hardware: DSLSAR (with Alcatel ADSL Module), State: up
IDB:     668DEA48  Instance: 668DFE6C  reg_dslsar:3C200000  wic_regs: 3C200080
PHY Inst:669116E4  Ser0Inst: 668CA5AC  Ser1Inst:  668D4808  us_bwidth:832  --------------------BURAYA DİKKAT------------------------------------------   
Slot:    0         Unit:     0         Subunit:   0         pkt Size: 4528    
VCperVP: 256       max_vp:   256       max_vc:    65536     total vc: 1       
rct_size:65536     vpivcibit:16        connTblVCI:8         vpi_bits: 8       
vpvc_sel:3         enabled:  0         throttled: 0         cell drops: 2       
Last Peridic Timer 05:19:24.264(19164264)
Parallel reads to TCQ:0  tx count reset = 0, periodic safe start = 0 
Attempts to overwrite SCC txring: 0
Host Controller lockup recovery Info:
       recovery count1= 0, recovery count2= 0
Saved Host Controller Info to check any lockup:
      scc = 0, output_qcount = 0, head:60,
      buf addr = 0x00000000, serial outputs = 950972
      scc = 1, output_qcount = 0, head:15,
      buf addr = 0x00000000, serial outputs = 271
Serial idb(AAL5) output_qcount:0 max:40
Serial idb(RAW) output_qcount:0, max:40
Sar ctrl queue: max depth = 0, current queue depth = 0, drops = 0, urun cnt = 0, total cnt = 271
Serial idb tx count: AAL5: 951227, RAW: 271, Drop count:AAL5: 0, RAW: 0
Host Controller Clock rate Info:
SCC Clockrates:
        SCC0 = 0
        SCC1 = 0
        SCC2 = 0
        SCC3 = 8000000 (ATM0/2/0) 
        SCC4 = 0
        SCC5 = 8000000 (ATM0/2/0) 
        SCC6 = 0
        SCC7 = 0
WIC    Register   Value      Notes
---------------   ---------- ----------
FPGA Dev ID (LB)  0x44       'D'
FPGA Dev ID (UB)  0x53       'S'
FPGA Revision     0xA8       
WIC Config Reg    0xD        WIC / VIC select = WIC; 
                             CTRLE addr bit 8 = 0; 
                             NTR Enable = 1; 
                             OK LED on; 
                             LOOPBACK LED off; 
                             CD LED on; 
WIC Config Reg2   0x07       Gen bus error on bad ADSL access
Int 0 Enable Reg  0x03       ADSL normal interrupt enabled
                             ADSL error interrupt enabled
DSLSAR Register   Value      Notes
---------------   ---------- ----------
sdram_refresh:    0x428FFFF  
intr_enable_reg:  0x43C      JUMPC.FBQE.RQAF.RPQAF.TSQAF.
config:           0x660D0A20 UTOPIA.RXEN.RegulateXmit.RMCell.TXEN.
                             Rx Buffer size: 8192.  RCT: Large, VPI Bits: 8.
status:           0x0       
clkPerCell:       4609254  (line rate: 832 Kbps) -----------------------------BURAYA DİKKAT-----------------------
Pre-timer Count:  471      
rcid_tableBase:   0x0       
rct_base:         0x11000   
tstBase1:         0x1B718    TST boot jump.
rawCellBase:      0x1C300    (0/128) slots used.
rpq_base:         0x1F000    
tsqb(Tx Stat Q):  0x1E000    
fbq_base:         0x1E880    (fbq_count: 128)
txChanQueue:      0x20000    
rxBuffers:        0x50000    
txBuffers:        0x150000   
Lookup Error cnt: 0x0        
Invalid Cell cnt: 0x0        
SCCA Rx Errors:   0x0       
SCCB Rx Errors:   0x0       
Drop Pkt Count:   0x0       
Total Tx Count:   0x272C    
Total Rx Count:   0x935A    
Timer:            0xCBA32C  
DSLSAR Interrupts:0xB       
     JMP-COMPLETE:0xA       
       FIFOF:     0x2       
       Timer:     0x2       


-----------------------------------------------------------
SH int atm 0/2/0
ATM0/2/0 is up, line protocol is up 
  Hardware is DSLSAR (with Alcatel ADSL Module)
  MTU 4470 bytes, sub MTU 4470, BW 832 Kbit/sec, DLY 610 usec, 
     reliability 255/255, txload 18/255, rxload 38/255
  Encapsulation ATM, loopback not set
  Encapsulation(s): AAL5  AAL2, PVC mode
  23 maximum active VCs, 256 VCs per VP, 1 current VCCs
  VC Auto Creation Disabled.
  VC idle disconnect time: 300 seconds
  Last input 03:05:22, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 13735
  Queueing strategy: Per VC Queueing
  30 second input rate 126000 bits/sec, 44 packets/sec
  30 second output rate 60000 bits/sec, 33 packets/sec
     1140953 packets input, 500355263 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 92 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     958547 packets output, 247945664 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out
SAYGILARIMLA


      

[Non-text portions of this message have been removed]



------------------------------------

--
Cisco Teknik Tartisma Listesi (Cisco-ttl)

Bu listede onerilen degisikliklerin uygulanmasindaki tum sorumluluk 
kullaniciya aittir. Liste yoneticileri, oneride bulunan liste uyeleri ya da 
bu uyelerin calistigi kuruluslar herhangi bir sekilde sorumlu tutulamazlar.Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/cisco-ttl/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/cisco-ttl/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:[email protected] 
    mailto:[email protected]

<*> To unsubscribe from this group, send an email to:
    [email protected]

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/