Re: MCEUSB transmit not working. Same codes send as receive. Hardware working fine.

An update.

I have this small snip of a config I tried and the OK button works on my 
IPTV box!

Now, why would this be?  Here is the remote config below.  Why would my 
receive config not work to transmit but this does?

I wish the config was complete but its not.  Only 3 keys....


begin remote
name ser1
flags RAW_CODES|CONST_LENGTH
eps 30
aeps 100

ptrail 0
repeat 0 0
gap 96946

begin raw_codes

name 1
450 150 300 200 200 600
200 200 250 700 250 350
250 200 250 200 250 200
250 200 200 550 200 400
250 550 200 250 250 200
200 250 150 450 200

name 2
500 150 300 150 250 550
250 200 200 750 200 400
200 250 200 200 250 200
250 550 200 600 200 400
150 600 200 250 200 250
200 250 200 550 200

name ok
500 200 200 250 200 550
250 200 150 800 250 350
250 200 250 200 150 300
200 250 200 550 200 400
200 600 200 400 200 400
200 750 200 250 200

end raw_codes
end remote


On 23/03/17 08:17 AM, Mark wrote:
> Hello,
>
> I am really close to getting this.  Just need some help to finish this 
> up please.
>
> A short description of what I am trying to do. I just need to change 
> channels in MythTV on a new device.
>
> Essentially, I am transmitting, but nothing is working and codes are 
> not activating device.
>
> ----------------------------
>
> To do this, I have:
>
> I have an IPTV box called a technicolor IPV5050 ( same codes as Cisco 
> IPN330HD ) that there are no known codes for.  So I used IRRecord to 
> build a config from the remote that came with the IPV5050.
>
> The receive portion of this works perfectly.  As the codes that are 
> setup to receive are also the same ones that I want to send, I am 
> thinking I should only have one device config.
>
> When I try to irsend, the command ( irsend SEND_ONCE mce KEY_OK ) is 
> accepted fine, and I can see the pulse on a camera coming out, but no 
> action on the IPTV box, or with another box listening with IRW. ( I 
> have two computer with the same config and receivers set up to test 
> this )
>
> Here are the configs and hardware info.  Any thoughts or advice 
> greatly appreciated.
>
> Fedora 25 and lirc 0.9.4C
>
> Hardware is an HP MCEUSB IR Receiver with the plug in transmitter 
> cable on the back.  I can see pulses when I try to transmit.
>
> --------------------------
>
> DMESG:
>
> [ 1072.293862] usb 1-7: new full-speed USB device number 9 using xhci_hcd
> [ 1072.464347] usb 1-7: New USB device found, idVendor=03ee, 
> idProduct=2501
> [ 1072.464352] usb 1-7: New USB device strings: Mfr=1, Product=2, 
> SerialNumber=3
> [ 1072.464355] usb 1-7: Product: eHome Infrared Transceiver
> [ 1072.464357] usb 1-7: Manufacturer: Mitsumi
> [ 1072.464360] usb 1-7: SerialNumber: MI001nxT
> [ 1072.465713] Registered IR keymap rc-rc6-mce
> [ 1072.465906] input: Media Center Ed. eHome Infrared Remote 
> Transceiver (03ee:2501) as 
> /devices/pci0000:00/0000:00:14.0/usb1/1-7/1-7:1.0/rc/rc0/input25
> [ 1072.466061] rc rc0: Media Center Ed. eHome Infrared Remote 
> Transceiver (03ee:2501) as 
> /devices/pci0000:00/0000:00:14.0/usb1/1-7/1-7:1.0/rc/rc0
> [ 1072.466249] rc rc0: lirc_dev: driver ir-lirc-codec (mceusb) 
> registered at minor = 0
> [ 1072.621897] mceusb 1-7:1.0: Registered Mitsumi eHome Infrared 
> Transceiver with mce emulator interface version 1
> [ 1072.621901] mceusb 1-7:1.0: 2 tx ports (0x1 cabled) and 2 rx 
> sensors (0x1 active)
>
> LIRC config:
>
> [root@ratty lircd.conf.d]# cat mce.lircd.conf
> # Please make this file available to others
> # by sending it to <[email protected]>
> #
> # this config file was automatically generated
> # using lirc-0.9.0(default) on Mon Mar 20 14:57:23 2017
> #
> # contributed by
> #
> # brand:                       own_remote.conf.conf
> # model no. of remote control:
> # devices being controlled by this remote:
> #
>
> begin remote
>
>   name  mce
>   bits            8
>   flags RCMM|CONST_LENGTH
>   eps            18
>   aeps          100
>
>   header        417   278
>   three         167   778
>   two           167   611
>   one           167   444
>   zero          167   278
>   ptrail        167
>   pre_data_bits   24
>   pre_data       0x248026
>   gap          99817
>   min_repeat 1
>   suppress_repeat 2
>   toggle_bit_mask 0x8000
>
> begin codes
>           KEY_1                    0x01
>           KEY_2                    0x02
>           KEY_3                    0x03
>           KEY_4                    0x04
>           KEY_5                    0x05
>           KEY_6                    0x06
>           KEY_7                    0x07
>           KEY_8                    0x08
>           KEY_9                    0x09
>           KEY_0                    0x00
>       KEY_POWER                0x0C
>           KEY_REWIND               0x29
>           KEY_STOP                 0x31
>           KEY_FASTFORWARD          0x28
>           KEY_PAUSE                0x2C
>           KEY_OK                   0x5C
>           KEY_VOLUMEUP             0x0C
>           KEY_CHANNELUP            0x20
>           KEY_CHANNELDOWN          0x21
>       end codes
>
> end remote
>
> # This is configuration is for the Motorola VIP 1200
> # 
> <http://broadband.motorola.com/catalog/productdetail.asp?ProductID=441> 
> and
> # VIP 1216
> # <http://broadband.motorola.com/catalog/productdetail.asp?ProductID=443>
> # STB provided by AT&T for their U-verse IPTV service
>
> LIRC OPTIONS file:
>
> [root@ratty lirc]# cat lirc_options.conf
> # Generated by lirc-setup
> [lircd]
> nodaemon = False
> driver = default
> device = /dev/lirc0
> output = /var/run/lirc/lircd
> pidfile = /var/run/lirc/lircd.pid
> plugindir = /usr/lib64/lirc/plugins
> permission = 666
> allow-simulate = No
> repeat-max = 600
> effective-user = lirc
> lircd_conf = mce.lircd.conf
>
> [lircmd]
> uinput = False
> nodaemon = False
>
> [modinit]
> code = echo lirc > /sys/class/rc/rc0/protocols
>
>
>


------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot