RE: How can I access the TINI IO Ports

Dear Jinq - You can buy the 1-Wire LCD controller "stand-alone" without
purchasing the display. Its a very standard 16 pin interface, used by many
LCD manufacturers.

Best regards, Kelly Smith

-----Original Message-----
From: tini-admin-6tN4nzCoH/[email protected] [mailto:[email protected]]On Behalf Of
Jing Qiu
Sent: Wednesday, March 10, 2004 5:53 PM
To: tini-6tN4nzCoH/[email protected]
Subject: RE: [TINI]How can I access the TINI IO Ports


Sounds good but I already got an LCD display, and it's
better to figure out how to use these parallel IO pins
because I want to interface some sensors to the board.

--- Kelly Smith <[email protected]> wrote: > Dear
Jinq - You could use the AAG Electronica's
> 1-Wire LCD display
> interfaced to TINI's 1-Wire I/O.  Ref:
> http://www.aagelectronica.com/aag/
>
> Click on:  1-Wire Sensors & Actuators, and the
> "Click here" after,
>
> TAI8590 1-Wire Text User Interface
>
> I have one and it works very nice; and includes
> provisions for switch
> closure detection.  It uses the DS2408 1-Wire 8-bit
> PIO.  So, you don't need
> ANY parallel I/O bits at all!
>
> "Based on the Dallas Semiconductor DS2408 the
> TAI8590 1-Wire Text User
> Interface allow you to connect a LCD Character
> display to your 1-Wire
> network and recieve messages from the host system.
> Also included in the
> module is the capability to connect push buttons to
> allow you to interact
> with the host program on your system. This module is
> fully compatible with
> the rest of  TAI 1-Wire devices. Software to test
> the module and Java
> classes are available at no cost in our Download
> Area."
>
> Best regards, Kelly Smith
>
> -----Original Message-----
> From: tini-admin-6tN4nzCoH/[email protected]
> [mailto:tini-admin-6tN4nzCoH/[email protected]]On Behalf Of
> Jing Qiu
> Sent: Wednesday, March 10, 2004 10:08 AM
> To: tini-6tN4nzCoH/[email protected]
> Subject: Re: [TINI]How can I access the TINI IO
> Ports
>
>
> Thanks. I want to connect an LCD to the DSTINIs400
> socket, but as you said, there's only a few IO port
> pins available. I see there are 32 user parallel IO
> pins available. How to use these user PIOs to access
> the data/address/control BUS?
>
>  --- Bryan Armstrong <bryan.armstrong-6tN4nzCoH/[email protected]>
> wrote: > Jing Qiu wrote:
> > > I'm using DSTINIs400 socket, could anybody show
> me
> > > where's the TINI IO ports, as I couldn't find
> them
> > on
> > > the datasheet.
> >
> > Look for pin names such as P0,P1,P2,P3,etc.  Some
> > ports are not
> > accessible as they are used for address/data/chip
> > enables.
> >
> > --
> > --
> > Bryan Armstrong
> > bryan.armstrong-6tN4nzCoH/[email protected]
> >
> >
>
>
______________________________________________________________________
> Post your free ad now! http://personals.yahoo.ca
> _______________________________________________
> TINI mailing list
> TINI-6tN4nzCoH/[email protected]
> To UNSUBSCRIBE, edit your profile, or see list
> archives:
> http://lists.dalsemi.com/mailman/listinfo/tini
>
>

______________________________________________________________________
Post your free ad now! http://personals.yahoo.ca
_______________________________________________
TINI mailing list
TINI-6tN4nzCoH/[email protected]
To UNSUBSCRIBE, edit your profile, or see list archives:
http://lists.dalsemi.com/mailman/listinfo/tini


_______________________________________________
TINI mailing list
TINI-6tN4nzCoH/[email protected]
To UNSUBSCRIBE, edit your profile, or see list archives:
http://lists.dalsemi.com/mailman/listinfo/tini