Re: Error in Multibank Load

I do not see the 400 loader banner on the second dump.

Are you sure you have DTR hooked up to the reset circuit, the same as in 
the reference hardware?

Abhijit Gadgil wrote:

>Hi Tom, 
>
>
>
>Following are the two Dumps. The first one, we are getting on the Tini 
>Board. And the second one we are getting on our custom board. This is 
>compiled using C51 compiler (7.06) and Ax51 Assembler (version 2.09)
>
>This is the dump on the TINI reference board, which we have. 
>---------------------------------------------------------------------
>  
>
>Loading file: D:\CURRENT\Apps.hex.
>
>Please wait... (ESC to abort.)
>
>DS80C400 Silicon Software - Copyright (C) 2002 Maxim Integrated 
>ProductsDetailed product information available at 
>http://www.maxim-ic.comWelcome to the TINI DS80C400 Auto Boot Loader 
>1.0.1
>  
>
>>Z40
>>    
>>
>
>You sure? Y
>
>  
>
>>DS80C400 Silicon Software - Copyright (C) 2002 Maxim Integrated 
>>    
>>
>ProductsDetailed product information available at 
>http://www.maxim-ic.comWelcome to the TINI DS80C400 Auto Boot Loader 
>1.0.1>B40
>
>  
>
>>T1 0 0
>>    
>>
>
>Desired size: 65536
>
>Read 65536 bytes.
>
>DS80C400 Silicon Software - Copyright (C) 2002 Maxim 
><snip>
>
>  
>
>>B40
>>    
>>
>
>  
>
>>C 0 FFFF
>>    
>>
>
>CRC = 04A6
>
>  
>
>
>DS80C400 Silicon Software - Copyright (C) 2002 Maxim Integrated 
><snip>
>
>  
>
>>Z41
>>    
>>
>
>You sure? Y
>
>  
>
>
>DS80C400 Silicon Software - Copyright (C) 2002 Maxim Integrated 
><snip>
>
>  
>
>>B41
>>T1 0 0
>>    
>>
>
>Desired size: 14210
>
>Read 14210 bytes.
>
>
>DS80C400 Silicon Software - Copyright (C) 2002 Maxim Integrated 
>ProductsDetailed product information available at 
>http://www.maxim-ic.comWelcome to the TINI DS80C400 Auto Boot Loader 
>1.0.1
>
>  
>
>>B41
>>    
>>
>
>  
>
>>C 0 3781
>>    
>>
>
>CRC = 61A2
>
>  
>
>
>DS80C400 Silicon Software - Copyright (C) 
><snip>
>
>  
>
>
>Load complete.
>
>  
>
>---------------------------------------------------------------------
>
>Here is the dump from our custom board. Somehow I am not able to get the C 
>command output on our custom board. Even with Verbose and Debug mode on.
>
>
>----------------------------------------------------------------------
>  
>
>Loading file: D:\CURRENT\Apps.hex.
>
>Please wait... (ESC to abort.)
>
>StartAddr: 0
>bankNum  : 40
>length   : 65536
>Accessing bank number: 40
>    Bank is Flash ROM...
>    Zapping bank...
>
>  
>
>>Z40
>>    
>>
>
>You sure? Y
>
>  
>
>    Loading file segment...
>
>  
>
>>B40
>>    
>>
>
>  
>
>>T1 0 0
>>    
>>
>
>Desired size: 65536
>Read 65536 bytes.
>        Checking CRC value... *Err* 
>
>*Err*
>
>No response from TINI board!
>
>
>------------------------------------------------------------------------
>
>
>On Thu, 15 Apr 2004, Thomas Chenot wrote:
>
>  
>
>>A dump of your debug messages might help. How are the hex files 
>>generated? Compiler? Assembler? Which compiler/assembler?
>>
>>Abhijit Gadgil wrote:
>>
>>    
>>
>>>Dear All, 
>>>
>>>We are facing a strange problem while loading a hex file as tbin on the 
>>>TINI when the size of the file is > 64K. This problem is occuring both 
>>>with the FLASH as well as RAM. This is a custom board designed by us. 
>>>Further, we are not having any problems while loading hex files < 64k. 
>>>
>>>When the debug and verbose mode is enabled, it is observed that the CRC 
>>>check after the first of the (target bank) is loaded fails. 
>>>
>>>Can anyone please throw some light on this?
>>>
>>>Regards,
>>>
>>>-abhijit
>>>      
>>>
>
>  
>


-- 
Thomas Chenot


_______________________________________________
TINI mailing list
TINI-6tN4nzCoH/[email protected]
To UNSUBSCRIBE, edit your profile, or see list archives:
http://lists.dalsemi.com/mailman/listinfo/tini