Re: Move fabric pool enabled aggregate to new disks

 Hi Alexander,

if you are on ONTAP 9.6+ and you want to use the same S3 bucket with your
new disks, vol move will only move the hot data to the new aggregates. The
cold data will remain on the cloud tier.
just take a look at this KB:
https://kb.netapp.com/Advice_and_Troubleshooting/Data_Storage_Software/ONTAP_OS/Why_does_volume_move_copy_cloud_tiered_data_on_releases_9.6_and_above


best regards
Tim

Am Mo., 22. März 2021 um 14:04 Uhr schrieb Alexander Griesser <
[email protected]>:

> Hey there,
>
>
>
> we’ve quite some fabric pool enabled aggregates and would want to move
> them to different disks. As far as I can see, there’s no good way to do
> that. Using vol moves will require to download all the data from our S3
> backend and re-upload it on the destination aggregate then.
>
> So say we want to „upgrade“ our fabric pool aggregate from 12x1TB SSD to
> 12x4TB SSD and let’s further assume that we have 20 volumes on the
> FP-enabled aggregate with a total of 1PB of storage in the S3 backend, do
> we really have to go through downloading and re-uploading all the data or
> is there an easier way (besides adding the new disks to the aggregate in
> the first step as spare disks and manually failing disk by disk) and
> afterwards increase the capacity in the raidgroup by addiding additional
> partitions?
>
>
>
> Best,
>
>
>
> *Alexander Griesser*
>
> Head of Systems Operations
>
>
>
> ANEXIA Internetdienstleistungs GmbH
>
>
>
> E-Mail: [email protected]
>
> Web: http://www.anexia-it.com
>
>
>
> Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt
>
> Geschäftsführer: Alexander Windbichler
>
> Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT
> U63216601
>
>
> _______________________________________________
> Toasters mailing list
> [email protected]
> https://www.teaparty.net/mailman/listinfo/toasters


Am Mo., 22. März 2021 um 14:04 Uhr schrieb Alexander Griesser <
[email protected]>:

> Hey there,
>
>
>
> we’ve quite some fabric pool enabled aggregates and would want to move
> them to different disks. As far as I can see, there’s no good way to do
> that. Using vol moves will require to download all the data from our S3
> backend and re-upload it on the destination aggregate then.
>
> So say we want to „upgrade“ our fabric pool aggregate from 12x1TB SSD to
> 12x4TB SSD and let’s further assume that we have 20 volumes on the
> FP-enabled aggregate with a total of 1PB of storage in the S3 backend, do
> we really have to go through downloading and re-uploading all the data or
> is there an easier way (besides adding the new disks to the aggregate in
> the first step as spare disks and manually failing disk by disk) and
> afterwards increase the capacity in the raidgroup by addiding additional
> partitions?
>
>
>
> Best,
>
>
>
> *Alexander Griesser*
>
> Head of Systems Operations
>
>
>
> ANEXIA Internetdienstleistungs GmbH
>
>
>
> E-Mail: [email protected]
>
> Web: http://www.anexia-it.com
>
>
>
> Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt
>
> Geschäftsführer: Alexander Windbichler
>
> Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT
> U63216601
>
>
> _______________________________________________
> Toasters mailing list
> [email protected]
> https://www.teaparty.net/mailman/listinfo/toasters

_______________________________________________
Toasters mailing list
[email protected]
https://www.teaparty.net/mailman/listinfo/toasters