Re: Re: error #20: identifier "TA0CCTL0_bit" is undefined....help on code composer

http://forum.allaboutcircuits.com/threads/msp430-multiplexed-7-segment-displays-errors.87703/

On Tue, Dec 9, 2014 at 7:37 AM, [email protected] [msp430] <
[email protected]> wrote:

>
>
> I am using the msp430g2553....
>
> I have enclosed the complete program below.....I believe the original
> software used iar to compile using "io430.h" header which I cannot use in
> code composer. I am new at this and am struggling with final project for a
> class. I have two marked lines with errors with ****** after //....
>
> Thanks Ted
>
> #include <msp430g2553.h>
> #include <msp430.h>
> #include <intrinsics.h>
> #include <stdint.h>
> //#include <io430.h>                  //.......??????why?
>
> #define NUMBER_OF_DIGITS 2
> #define TACCTL0_               TA0CCTL0_      /* Timer A Capture/Compare
> Control 0 */
> #define TACCTL1_               TA0CCTL1_      /* Timer A Capture/Compare
> Control 1 */
> #define DELAY 1000
> #define TIMER_DELAY 630
> #define CCIE                   (0x0010)       /* Capture/compare interrupt
> enable */
> char seg[16];
> char d[5];
> char digit;
> short v;
>
> // simple software delay
> void delay(unsigned long d)
> {
>   unsigned long i;
>   for (i = 0; i < d; i++);
> }
>
> void display_hex(unsigned short v)
> { // enter with 16-bit integer v
>   // fill global array d[ ]
>   short i;
>   for (i = 0; i < 4; i++)
>   {
>      d[i] = v % 16;
>      v = v/16;
>   }
> }
>
> void display_BCD(unsigned short v)
> {// enter with 16-bit integer v
>  // fill global array d[ ]
>   short i;
>   for (i = 0; i < 5; i++)
>   {
>      d[i] = v % 10;
>      v = v/10;
>   }
> }
>
> #pragma vector = TIMER0_A0_VECTOR
> __interrupt void myTimerISR(void)
> {
>   digit = ++digit % NUMBER_OF_DIGITS;   //use MOD operator
>   P1OUT = ~seg[d[digit]];
>   P2OUT = 1 << digit;
> }
>
> void init(void)
> {
>   // Stop watchdog timer to prevent time out reset
>   WDTCTL = WDTPW + WDTHOLD;
>
>   // initialize Timer0_A
>   TA0CCR0 = TIMER_DELAY;                  // set up terminal count
>   TA0CTL = TASSEL_2 + ID_3 + MC_1;  // configure and start timer
>
>   // enable interrupts
>   TA0CCTL0_bit.CCIE = 1;   // enable timer interrupts********
>   __enable_interrupt();    // set GIE in SR**********
>
>   P1DIR  = 0xFF;       // enable segment outputs
>   P2DIR  = 0x0F;   // enable digit select
>
>   // create 7-segment table
>   seg[0]  = 0x3F;
>   seg[1]  = 0x06;
>   seg[2]  = 0x5B;
>   seg[3]  = 0x4F;
>   seg[4]  = 0x66;
>   seg[5]  = 0x6D;
>   seg[6]  = 0x7D;
>   seg[7]  = 0x07;
>   seg[8]  = 0x7F;
>   seg[9]  = 0x67;
>   seg[10] = 0x77;
>   seg[11] = 0x7C;
>   seg[12] = 0x39;
>   seg[13] = 0x5E;
>   seg[14] = 0x79;
>   seg[15] = 0x71;
>
>   digit = 0;
> }
>
> void initADC(void)
> {
>   // initialize 10-bit ADC
>   ADC10CTL1 = INCH_7 + CONSEQ_2; // use P1.7 (channel 7)
>   ADC10CTL0 |= ADC10SHT_3 + ADC10ON + MSC;
>   ADC10AE0 |= BIT7; // enable analog input on channel 7
>   ADC10CTL0 |= ADC10SC + ENC; // start conversions
> }
>
> void main( void )
> {
>  init();
>  initADC();
>
>  while (1)
>  {
>    v = ADC10MEM;
>    display_BCD(v);
>    delay(DELAY);
>  }
>
> }
>
> 
>