Problem compiling ti example code...

I am trying to use mspgcc on my Mac, 10.8.3.

I have managed to build mspgcc but now I can't use it to build the examples
from ti (for the launchpad).

This is the code:

//******************************************************************************
//  MSP430G2xx1 Demo - Timer_A, Toggle P1.0-2, Cont. Mode ISR, DCO SMCLK
//
//  Description: Use Timer_A CCRx units and overflow to generate four
//  independent timing intervals. For demonstration, CCR0 and CCR1 output
//  units are optionally selected with port pins P1.1 and P1.2 in toggle
//  mode. As such, these pins will toggle when respective CCRx registers
match
//  the TAR counter. Interrupts are also enabled with all CCRx units,
//  software loads offset to next interval only - as long as the interval
offset
//  is aded to CCRx, toggle rate is generated in hardware. Timer_A overflow
ISR
//  is used to toggle P1.0 with software. Proper use of the TAIV interrupt
//  vector generator is demonstrated.
//  ACLK = n/a, MCLK = SMCLK = TACLK = default DCO ~1MHz
//  As coded and assuming ~1MHz DCO, toggle rates are:
//  P1.1 = CCR0 ~ 1MHz/(2*200) ~2500Hz
//  P1.2 = CCR1 ~ 1MHz/(2*1000) ~500Hz
//  P1.0 = overflow ~ 1MHz/(2*65536) ~8Hz
//
//               MSP430G2xx1
//            -----------------
//        /|\|              XIN|-
//         | |                 |
//         --|RST          XOUT|-
//           |                 |
//           |         P1.1/TA0|--> CCR0
//           |         P1.2/TA1|--> CCR1
//           |             P1.0|--> Overflow/software
//
//  D. Dang
//  Texas Instruments Inc.
//  October 2010
//  Built with CCS Version 4.2.0 and IAR Embedded Workbench Version: 5.10
//******************************************************************************

#include <msp430.h>

int main(void)
{
  WDTCTL = WDTPW + WDTHOLD;                 // Stop WDT
  P1SEL |= 0x06;                            // P1.1 - P1.2 option select
  P1DIR |= 0x07;                            // P1.0 - P1.2 outputs
  CCTL0 = OUTMOD_4 + CCIE;                  // CCR0 toggle, interrupt
enabled
  CCTL1 = OUTMOD_4 + CCIE;                  // CCR1 toggle, interrupt
enabled
  TACTL = TASSEL_2 +  MC_2 + TAIE;          // SMCLK, Contmode, int enabled

  _BIS_SR(LPM0_bits + GIE);                 // Enter LPM0 w/ interrupt
}

// Timer A0 interrupt service routine
#pragma vector=TIMERA0_VECTOR
__interrupt void Timer_A0 (void)
{
  CCR0 += 200;                              // Add Offset to CCR0
}

// Timer_A2 Interrupt Vector (TAIV) handler
#pragma vector=TIMERA1_VECTOR
__interrupt void Timer_A1(void)
{
  switch( TAIV )
  {
  case  2: CCR1 += 1000;                    // Add Offset to CCR1
           break;
  case 10: P1OUT ^= 0x01;                   // Timer_A3 overflow
           break;
 }
}


And to build it I use:

$ msp430-gcc -mmcu=msp430g2231 -o test.hex test.c -I
/usr/local/msp430/include/ -L /usr/local/msp430/lib/ -T
/usr/local/msp430/lib/ldscripts/msp430g2231/memory.x -T
/usr/local/msp430/lib/ldscripts/msp430g2231/periph.x

Resulting in:

/usr/local/bin/msp430-ld: test.hex section `.init9' will not fit in region
`ram'
/usr/local/bin/msp430-ld: region `ram' overflowed by 10 bytes
collect2: ld returned 1 exit status

Surely this code can't be to large to fit the device, so what am I missing?


Thanks in advance.
Einar

------------------------------------------------------------------------------
Minimize network downtime and maximize team effectiveness.
Reduce network management and security costs.Learn how to hire 
the most talented Cisco Certified professionals. Visit the 
Employer Resources Portal
http://www.cisco.com/web/learning/employer_resources/index.html

_______________________________________________
Mspgcc-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/mspgcc-users