Re: using in-board ez430 FET emulator
Eric Decker <[email protected]>
| Newsgroups | gmane.comp.hardware.texas-instruments.msp430.gcc.user |
|---|---|
| Message-ID | <CAMdX_2DVJwzaGoJCQYkfNLex=NP0Xta6Nir=vYYAKRi3JeaZzQ@mail.gmail.com> |
What version of msp430-gdb are you running? Where did you get it? do.. dpkg -l "*msp430*" and how do you have apt configured? What repository are you using to get the tools from? On Sat, Jun 22, 2013 at 5:10 PM, John Willauer <[email protected]> wrote: > How do I eliminate the "Segmentation fault" that occurs when I start > msp430-gdb using the following procedure Jose Luis Honorato described in > his response to Ravim. > > When the msp430-gdb is started, in the second shell, a Segmentation fault > is reported then the msp430-gdb terminates. > > I am trying to use gdb to debug code running on a Launchpad with a > msp430g2553 chip. > > > -- > John > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > > > On 06/22/2013 01:06 PM, Eric Decker wrote: > > > Just asking how to get rid of a "seg fault" isn't to helpful. > > What program was actually running? What version? What address? > > > On Sat, Jun 22, 2013 at 11:55 AM, John Willauer <[email protected]>wrote: > >> How do I eliminate the "Segmentation fault" I get when I try it using: >> >> Ubuntu 12.04 >> mspdebug 0.18-1 >> gdb-msp430 7.2~mspgcc-7.2.2 >> gcc-msp439 4.5.3~mspgcc-201 >> >> -- >> John >> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - >> >> >> >> On 06/20/2013 09:53 AM, Jose Luis Honorato L. wrote: >> >>> Hi Ravim, >>> >>> I can't see the output messages you intended to include, but here's a >>> short >>> how-to. I just hope you don't have a specific problem with your setup. >>> >>> You can use the ez430-FET emulator to program the msp-exp430f5529 without >>> any external hardware. Just plug your mini USB cable to the lower left >>> USB >>> connector (the one in the ez430-FET emulator) and run: >>> >>> sudo mspdebug rf2500 "prog bin.elf" >>> >>> That should program the device after a few console messages. >>> >>> You can use mspdebug with gdb too, for that you should: >>> >>> 1. Run mspdebug (sudo mspdebug rf2500) >>> 2. In mspdebug, type gdb >>> 3. In another window, run msp430-gdb >>> 4. In gdb, type target remote localhost:2000 >>> 5. Done >>> >>> This is assuming you have all these tools installed, if not there are >>> plenty of guides out there on how to install them. >>> >>> Kind regards, >>> Jose >>> _______________________________________________ >>> Mspgcc-users mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/mspgcc-users >>> >> >> >> >> >> ------------------------------------------------------------------------------ >> This SF.net email is sponsored by Windows: >> >> Build for Windows Store. >> >> http://p.sf.net/sfu/windows-dev2dev >> _______________________________________________ >> Mspgcc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/mspgcc-users >> >> > > > -- > Eric B. Decker > Senior (over 50 :-) Researcher > > > -- Eric B. Decker Senior (over 50 :-) Researcher ------------------------------------------------------------------------------ This SF.net email is sponsored by Windows: Build for Windows Store. http://p.sf.net/sfu/windows-dev2dev _______________________________________________ Mspgcc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/mspgcc-users