RE: User/Group issues

Thanks Vlada,

Adding the reevaluateAssignments(); solved my issues.

> -----Original Message-----
> From: Vladimir Puskas [mailto:[email protected]] 
> Sent: Monday, July 18, 2005 5:42 AM
> To: [email protected]
> Subject: Re: [shark] User/Group issues
> 
> 
> Hello Greg
> 
> you wrote:
> > As a follow up to this - it may be the second issued listed 
> below is 
> > because the 2nd user I created and mapped to "GroupTwo" was 
> done AFTER 
> > the process was instantiated.
> > 
> > So I guess another question I have is:
> > 
> > 4) If I have an existing process that is not accepted by anyone in 
> > that group, and I add a new user to that group, the new user will 
> > never see the activity waiting for acceptance???
> 
> No, unless you do SharkAdmin-> Process Instantiation Mgmt -> 
> Reevaluate 
> Assignments.
> 
> >>-----Original Message-----
> >>From: Dahl, Greg (BLM) - contr
> >>Sent: Friday, July 15, 2005 2:36 PM
> >>To: [email protected]
> >>Subject: [shark] User/Group issues
> >>
> >>
> >>I'm getting a couple odd responses from the administration
> >>application:
> >>
> >>1) I created a new user using the admin application, but it
> >>does not show up in the drop down list on the worklist 
> >>management tab.  Is there a limit to the number of users that 
> >>can appear in the "Select User" drop down.  I have verified 
> >>the user is properly set up in the UserTable, UserGroupTable, 
> >>and the GroupTable.
> 
> Shark Admin is in fact a demo application, so there are rough edges, 
> like this one. User Management tab works directly with 
> appropriate Shark 
> API, while drop-down list (in worklist mgmt) is filled from Shark's 
> working instances: WfResources. Once you log in with new user 
> credentials, on when this user gets first assignment - admin 
> will show 
> her ;-)
> 
> >>2) I created two users and assigned them both to "GroupTwo".
> >>In the User Management tab (of the administration 
> >>application), I mapped the processes first participant to 
> >>"GroupOne" and second participant to "GroupTwo".
> >>
> >>When I look a the first user's worklist, I see the processes
> >>that are currently assigned to "GroupTwo" because that user 
> >>is a member of that group.  But when I look at the second 
> >>user's worklist, I do not see anything.  Again, I compared 
> >>the UserTable, GroupTable, and UserGroupTable and do not see 
> >>anything suspicious
>  >
> >>3) I created a user and assigned it to both "GroupOne" and
> >>"GroupTwo". But this user only sees records assigned to 
> >>GroupTwo, it never sees the GroupOne records.  However, a 
> >>user assigned to GroupOne only CAN see the GroupOne records?
> 
> Answer for (4) should help, it should probably has to do with 
> sequence 
> of creating users, their WfResource objects, and creating/starting 
> process...
> 
> hope this helps
> -- 
> Vlada
> 
> 
******* Confidentiality Notice *******
This email, its electronic document attachments, and the contents of its website linkages may contain confidential health information.  This information is intended solely for use by the individual or entity to whom it is addressed.  If you have received this information in error, please notify the sender immediately and arrange for the prompt destruction of the material and any accompanying attachments.

--
You receive this message as a subscriber of the [email protected] mailing list.
To unsubscribe: mailto:[email protected]
For general help: mailto:[email protected]?subject=help
ObjectWeb mailing lists service home page: http://www.objectweb.org/wws