Re: clamav at fresh installation

Hi Eric.
It is on CentOS7 fresh installation
Greetings, ladas
Eric B Munson píše v St 20. 02. 2019 v 14:37 -0500:
> What distribution is this on?  Is this a new install or an update?
> 
> On 2019-02-18 11:31, L.Slanina wrote:
> > 
> > Hi everybody.
> > 
> > Can someone help with clamav problem please? Thank you very much.
> > 
> > Greetings ladas
> > 
> > During "kolab-settings" configuration I got this message:
> > 
> > Kolab Service password [******************]:
> > ERROR: Can't open /var/log/clamav/freshclam.log in append mode
> > (check
> > permissions!).
> > ERROR: Problem with internal logger (UpdateLogFile =
> > /var/log/clamav/freshclam.log).
> > Job for [email protected] failed because start of the service
> > was
> > attempted too often. See "systemctl status [email protected]"
> > and
> > "journalctl -xe" for details.
> > To force a start use "systemctl reset-failed [email protected]"
> > followed by "systemctl start [email protected]" again.
> > Created symlink from
> > /etc/systemd/system/multi-user.target.wants/amavisd.service to
> > /usr/lib/systemd/system/amavisd.service.
> > 
> > And when I force to start and check clamav daemon does not work:
> > 
> > systemctl status [email protected]
> > ● [email protected] - clamd scanner (amavisd) daemon
> >    Loaded: loaded (/etc/systemd/system/[email protected]; enabled;
> > vendor
> > preset: disabled)
> >    Active: failed (Result: start-limit) since Po 2019-02-18
> > 17:25:36
> > CET; 10s ago
> >      Docs: man:clamd(8)
> >            man:clamd.conf(5)
> >            https://www.clamav.net/documents/
> >   Process: 3826 ExecStart=/usr/sbin/clamd -c /etc/clamd.d/%i.conf
> > (code=exited, status=1/FAILURE)
> > 
> > úno 18 17:25:36 kolab.mydomain.local  systemd[1]:
> > [email protected]: control process exited, code=exited...us=1
> > úno 18 17:25:36  kolab.mydomain.local systemd[1]: Failed to start
> > clamd scanner (amavisd) daemon.
> > úno 18 17:25:36  kolab.mydomain.local systemd[1]: Unit
> > [email protected] entered failed state.
> > úno 18 17:25:36  kolab.mydomain.local systemd[1]:
> > [email protected] failed.
> > úno 18 17:25:36  kolab.mydomain.local systemd[1]:
> > [email protected] holdoff time over, scheduling restart.
> > úno 18 17:25:36  kolab.mydomain.local systemd[1]: Stopped clamd
> > scanner (amavisd) daemon.
> > úno 18 17:25:36  kolab.mydomain.local systemd[1]: start request
> > repeated too quickly for [email protected]
> > úno 18 17:25:36  kolab.mydomain.local systemd[1]: Failed to start
> > clamd scanner (amavisd) daemon.
> > úno 18 17:25:36  kolab.mydomain.local systemd[1]: Unit
> > [email protected] entered failed state.
> > úno 18 17:25:36  kolab.mydomain.local systemd[1]:
> > [email protected] failed.
> > Hint: Some lines were ellipsized, use -l to show in full.
> > _______________________________________________
> > users mailing list
> > [email protected]
> > https://lists.kolab.org/mailman/listinfo/users
> _______________________________________________
> users mailing list
> [email protected]
> https://lists.kolab.org/mailman/listinfo/users

_______________________________________________
users mailing list
[email protected]
https://lists.kolab.org/mailman/listinfo/users