RE: Errors when doing 'use Tk::ExecuteCommand'

Thanks for the help.

Here is what the installation process shows:

perl Makefile.PL
/home/b06reg/sources/Tk-ExecuteCommand-1.6 does not start with
/usr/local/lib/perl5/site_perl/5.8.8/aix
i.e. building outside Tk itself
Checking if your kit is complete...
Looks good
Writing Makefile for Tk::ExecuteCommand
bash-2.04# make
cp ExecuteCommand.pm blib/lib/Tk/ExecuteCommand.pm
cp Killfam.pm blib/lib/Tk/../Proc/Killfam.pm
Manifying blib/man3/Tk::ExecuteCommand.3
Manifying blib/man3/Tk::Killfam.3
bash-2.04# make install
Writing /usr/local/lib/perl5/site_perl/5.8.8
/aix/auto/Tk/ExecuteCommand/.packlist
Appending installation info to /usr/local/lib/perl5/5.8.8/aix/perllocal.pod

Here is what I get when I run the short perl command you listed:

Can't load '/usr/local/lib/perl5/site_perl/5.8.8
/aix/auto/Proc/ProcessTable/ProcessTable.so' for module Proc::ProcessTable:
rtld: 0712-001 Symbol __floatdidf was referenced
      from module /usr/local/lib/perl5/site_perl/5.8.8
/aix/auto/Proc/ProcessTable/ProcessTable.so(), but a runtime definition
      of the symbol was not found.
rtld: 0712-001 Symbol __cmpdi2 was referenced
      from module /usr/local/lib/perl5/site_perl/5.8.8
/aix/auto/Proc/ProcessTable/ProcessTable.so(), but a runtime definition
      of the symbol was not found.
rtld: 0712-001 Symbol __floatdisf was referenced
      from module /usr/local/lib/perl5/site_perl/5.8.8
/aix/auto/Proc/ProcessTable/ProcessTable.so(), but a runtime definition
      of the symbol was not found. at /usr/local/lib/perl5/5.8.8
/aix/DynaLoader.pm line 230.
 at -e line 0
Compilation failed in require.
BEGIN failed--compilation aborted.

Ray Gebbie
Federated Systems Group
San Francisco, CA 94102
415-422-1662



                                                                           
             <marek.rouchal@in                                             
             fineon.com>                                                   
                                                                        To 
             11/19/2006 11:11          <[email protected]>                
             PM                                                         cc 
                                       <[email protected]>            
                                                                   Subject 
                                       RE: Errors when doing 'use          
                                       Tk::ExecuteCommand'                 
                                                                           
                                                                           
                                                                           
                                                                           
                                                                           
                                                                           




What happens when you run
             <your-path-to-perl>/perl -MProc::ProcessTable -e 1
Does this module load OK?
Proc::ProcessTable has some compiled parts in it, are you
sure its entire build process
             perl Makefile.PL
             make
             make test
             make install
was OK?

HTH,

Marek


-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Ray Gebbie
Sent: Saturday, November 18, 2006 1:40 AM
To: [email protected]
Subject: Errors when doing 'use Tk::ExecuteCommand'


I get the following error when my script starts up:

Proc::ProcessTable missing, can't kill sub-children. at
/usr/local/lib/perl5/site_perl/5.8.8/aix/Proc/Killfam.pm line 19.
 at /usr/local/lib/perl5/site_perl/5.8.8/aix/Proc/Killfam.pm line 19
        Proc::Killfam::BEGIN() called at
/usr/local/lib/perl5/site_perl/5.8.8/aix/Proc/Killfam.pm line 21
        eval {...} called at /usr/local/lib/perl5/site_perl/5.8.8
/aix/Proc/Killfam.pm line 21
        require Proc/Killfam.pm called at
/usr/local/lib/perl5/site_perl/5.8.8/Tk/ExecuteCommand.pm line 6
        Tk::ExecuteCommand::BEGIN() called at
/usr/local/lib/perl5/site_perl/5.8.8/aix/Proc/Killfam.pm line 21
        eval {...} called at /usr/local/lib/perl5/site_perl/5.8.8
/aix/Proc/Killfam.pm line 21
        require Tk/ExecuteCommand.pm called at
/home/release/scripts/newpromote.pl line 4
        main::BEGIN() called at /usr/local/lib/perl5/site_perl/5.8.8
/aix/Proc/Killfam.pm line 21
        eval {...} called at /usr/local/lib/perl5/site_perl/5.8.8
/aix/Proc/Killfam.pm line 21

The start of my script is:

   #!/usr/bin/perl
   use Tk;
   use Tk::ExecuteCommand;
   use Proc::ProcessTable;
   use Tk::MiniCalendar;
   use Tk::LabFrame;
   use Tk::FBox;
   use Tk::LabEntry;

I am running on AIX 5.3 using perl version 5.8.8.  I added the following
modules with no errors reported:

Proc-ProcessTable-0.41
Tk-ExecuteCommand-1.6

I seem to be able to ignore the error and continue to run the script.
But
I would like to not have these errors show up.

Anybody know what is happening?

Ray Gebbie
Federated Systems Group
San Francisco, CA 94102
415-422-1662

--++**==--++**==--++**==--++**==--++**==--++**==--++**==
ptk mailing list
[email protected]
https://mailman.stanford.edu/mailman/listinfo/ptk
--++**==--++**==--++**==--++**==--++**==--++**==--++**==
ptk mailing list
[email protected]
https://mailman.stanford.edu/mailman/listinfo/ptk