Re: Calling a seaside component from a table row
Karsten Kusche <[email protected]> Thu, 4 Feb 2021 14:48:01 +0000
| Newsgroups | gmane.comp.lang.smalltalk.squeak.seaside |
|---|---|
| Message-ID | <[email protected]> |
Hi Annick, Esteban said the „container-id“ has to be in the DOM. The new components will only be rendered when requested via Ajax. Kind regards Karsten — Georg Heeg eK Wallstraße 22 06366 Köthen Tel.: 03496/214328 FAX: 03496/214712 Amtsgericht Dortmund HRA 12812 Am 4. Februar 2021 um 15:44:45, List ([email protected]<mailto:[email protected]>) schrieb: Hi Esteban, Thank you for the update, but my web pages are big, and having all of them in one single DOM will be huge. Otherwise, this was helpful. Kind regards Annick Le 4 févr. 2021 à 15:40, Esteban Maringolo <[email protected]<mailto:[email protected]>> a écrit : Hi Annick, It is exactly as Karsten suggests, you usually replace a component by another one, depending on your needs you might use the call/answer, show or simply replace the component (the most common use). html tableRow onClick: ((html jQuery id: 'containerId') ajax html: [:h | h render: YourComponent new]); this will render YourComponent within a <div> with id 'containerId', that must exist in the DOM before making the call. regards Esteban A. Maringolo On Thu, Feb 4, 2021 at 8:51 AM Karsten Kusche <[email protected]<mailto:[email protected]>> wrote: Typically you use #call: to have the original component replace itself with another component and then this other component decides when to return by calling #answer:. If you move this task to the surrounding component, it can replace the sub-component any time, without the need for a #call:. This approach should be possible from Ajax, too: you basically replace the component and redraw the cell. Karsten — Georg Heeg eK Wallstraße 22 06366 Köthen Tel.: 03496/214328 FAX: 03496/214712 Amtsgericht Dortmund HRA 12812 Am 4. Februar 2021 um 10:46:41, List ([email protected]<mailto:[email protected]>) schrieb: Thank you Karsten, Do you have any suggestion then outside putting an anchor in each cell ? Kind regards Annick Le 4 févr. 2021 à 10:45, Karsten Kusche <[email protected]<mailto:[email protected]>> a écrit : Hi Annick, performing a #call: from within a Ajax callback typically doesn’t work in Seaside. Kind Regards Karsten — Georg Heeg eK Wallstraße 22 06366 Köthen Tel.: 03496/214328 FAX: 03496/214712 Amtsgericht Dortmund HRA 12812 Am 4. Februar 2021 um 10:42:44, List ([email protected]<mailto:[email protected]>) schrieb: Hi, I would like to call a new component from a table row as in the following <tr onclick=« callmycomponent…> I have tried html tableRow onClick: (html jQuery callback: [self callMyComponent]) but the callback is called and I stay on the same page Best regards Annick _______________________________________________ seaside mailing list [email protected]<mailto:[email protected]> http://lists.squeakfoundation.org/cgi-bin/mailman/listinfo/seaside _______________________________________________ seaside mailing list [email protected]<mailto:[email protected]> http://lists.squeakfoundation.org/cgi-bin/mailman/listinfo/seaside _______________________________________________ seaside mailing list [email protected]<mailto:[email protected]> http://lists.squeakfoundation.org/cgi-bin/mailman/listinfo/seaside _______________________________________________ seaside mailing list [email protected] http://lists.squeakfoundation.org/cgi-bin/mailman/listinfo/seaside _______________________________________________ seaside mailing list [email protected] http://lists.squeakfoundation.org/cgi-bin/mailman/listinfo/seaside