Re: Downgrading eBible.org ftp repository service; upgrading https service

AHA!

now I feel dumb... the couple of modules I just tried install fine IF I
check the checkbox on the line item. apparently it's not adequate to just
select the line.

has that always been the case? I don't remember. I installed a bunch of
modules years ago and now only seldom install anymore, so maybe I just
forgot.

Fred


On Fri, Feb 28, 2025 at 2:56 PM David Haslam <dfhdfh-g/[email protected]> wrote:

> Thanks Fred,
>
> I just successfully installed modules
>
>    - *engLXX2012eb*
>    - *engUKLXX2012eb*
>
> Those are the only English LXX modules I could find beyond the *Brenton
> Septuagint Translation*, the one I am still unable to install.
>
> *Any clues yet, Michael?*
>
> Best regards,
>
> David
>
> Sent with Proton Mail <https://proton.me/mail/home> secure email.
>
> On Friday, February 28th, 2025 at 6:58 PM, Fred <[email protected]>
> wrote:
>
> David, not under ancient greek, but it is under English. All the ones I
> tried are English unless otherwise stated.
>
> On Fri, Feb 28, 2025 at 1:34 PM David Haslam <[email protected]>
> wrote:
>
>> Hi Fred,
>>
>> AFAICT, there's no LXX module under the language Κοινή Ἑλληνῐκή (*aka*
>> Ancient Greek) in the *eBible.org* repo.
>>
>>
>>    1. What's the actual ModName of the one you tried to install?
>>    2. Under which language did Xiphos list it?
>>
>>
>> Best regards,
>>
>> David
>>
>> Sent with Proton Mail <https://proton.me/mail/home> secure email.
>>
>> On Friday, February 28th, 2025 at 6:01 PM, Fred <[email protected]>
>> wrote:
>>
>> Hmmm. after I choose the LXX module and click install there is a pause of
>> 1 or 2 seconds but no progress bar.
>> it looks as if following Scott's directions above worked correctly...
>> see attached files.
>>
>> On Fri, Feb 28, 2025 at 12:06 PM David Haslam <[email protected]>
>> wrote:
>>
>>> I was also able to successfully install the *TNT* module *engtnteb* via
>>> HTTPS from eBible.org
>>>
>>> i.e. After adding the HTTPS module source to *Xiphos* as described in
>>> the thread.
>>>
>>> Best regards,
>>>
>>> David
>>>
>>> Sent with Proton Mail <https://proton.me/mail/home> secure email.
>>>
>>> On Friday, February 28th, 2025 at 4:06 PM, Fred <[email protected]>
>>> wrote:
>>>
>>>
>>> Scott, thanks for the recipe. I've done that and everything looks as if
>>> I did it right, but when I attempt to install a module from eBible nothing
>>> is installed, or not that I can find, not even by perusing the filesystem
>>> under ~/.sword. I ran Xiphos from the commandline and did it again, but no
>>> error messages appeared.
>>>
>>> Clues? (I have none!)
>>>
>>> Fred
>>>
>>> On Fri, Feb 28, 2025 at 9:06 AM David Haslam <[email protected]>
>>> wrote:
>>>
>>>> *PostScript*:
>>>>
>>>> I was able to successfully install the YLT module *engylt1898eb* via
>>>> HTTPS.
>>>>
>>>> So why the problem with the Brenton module?
>>>>
>>>> Best regards,
>>>>
>>>> David
>>>>
>>>> Sent with Proton Mail <https://proton.me/mail/home> secure email.
>>>>
>>>> On Friday, February 28th, 2025 at 1:47 PM, David Haslam <
>>>> dfhdfh-g/[email protected]> wrote:
>>>>
>>>> I did that and then tried to install module *engBrent1851eb*
>>>>
>>>> *Xiphos* gave the error message "Install Failed" (just like it did for
>>>> FTP).
>>>>
>>>> Best regards,
>>>>
>>>> David
>>>>
>>>> Sent with Proton Mail <https://proton.me/mail/home> secure email.
>>>>
>>>>
>>>> On Friday, February 28th, 2025 at 12:19 PM, Scott Buchanan
>>>> scott-lwzoXI5syOZtdF/[email protected] wrote:
>>>>
>>>> On 27/02/2025 22:32, Fred wrote:
>>>>
>>>> As a Xiphos user, is there anything I can do to update my Xiphos to
>>>> use https? It seems to default to ftp.
>>>>
>>>> If you go to Edit > Module Manager > Module Sources > Add/Remove >
>>>>
>>>> Current Remote Sources > Add and use the following details
>>>>
>>>> Caption: eBible.org HTTPS
>>>> Type: HTTPS
>>>> Host: ebible.org
>>>> Directory: /sword
>>>> User: (leave blank)
>>>> Password: (leave blank)
>>>>
>>>> Then click Refresh on that page, you should now have the eBible.org
>>>> HTTPS source added. Do the usual to access it as you would any other
>>>> Xiphos module source.
>>>>
>>>> I don't think there's an easy way to change all of the sources to HTTPS,
>>>> they must be added individually. I've opened a GitHub issue
>>>> (https://github.com/crosswire/xiphos/issues/1214) for this, updates
>>>> will
>>>> be posted there and likely on the xiphos-devel mailing list too.
>>>>
>>>> --
>>>>
>>>> Best regards,
>>>> Scott.
>>>>
>>>> _______________________________________________
>>>> sword-devel mailing list: [email protected]
>>>> http://crosswire.org/mailman/listinfo/sword-devel
>>>> Instructions to unsubscribe/change your settings at above page
>>>>
>>>>
>>>> _______________________________________________
>>>> sword-devel mailing list: [email protected]
>>>> http://crosswire.org/mailman/listinfo/sword-devel
>>>> Instructions to unsubscribe/change your settings at above page
>>>>
>>>
>>> _______________________________________________
>>> sword-devel mailing list: [email protected]
>>> http://crosswire.org/mailman/listinfo/sword-devel
>>> Instructions to unsubscribe/change your settings at above page
>>>
>>
>> _______________________________________________
>> sword-devel mailing list: [email protected]
>> http://crosswire.org/mailman/listinfo/sword-devel
>> Instructions to unsubscribe/change your settings at above page
>>
>
> _______________________________________________
> sword-devel mailing list: [email protected]
> http://crosswire.org/mailman/listinfo/sword-devel
> Instructions to unsubscribe/change your settings at above page
>

_______________________________________________
sword-devel mailing list: [email protected]
http://crosswire.org/mailman/listinfo/sword-devel
Instructions to unsubscribe/change your settings at above page