Re: Downgrading eBible.org ftp repository service; upgrading https service
Kahunapule Michael Johnson <[email protected]>
| Newsgroups | gmane.comp.literature.sword.devel |
|---|---|
| Organization | http://eBible.org |
| Message-ID | <[email protected]> |
I am still baffled as to why installation of engLXX2012eb and engUKLXX2012eb work fine, but engBrent1851eb, the predecessor to both of the previous ones, does not. I did, however, manage to duplicate the failure in Bishop running on an Android phone. This isn't a server issue, though. On 2/28/25 09:55, David Haslam wrote: > Thanks Fred, > > I just successfully installed modules > > * *engLXX2012eb* > * *engUKLXX2012eb* > > Those are the only English LXX modules I could find beyond the *Brenton Septuagint Translation*, the one I am stillunable to install. > > /Any clues yet, Michael?/ > > Best regards, > > David > > Sent with Proton Mail <https://proton.me/mail/home> secure email. > > On Friday, February 28th, 2025 at 6:58 PM, Fred <[email protected]> wrote: >> David, not under ancient greek, but it is under English. All the ones I tried are English unless otherwise stated. >> >> On Fri, Feb 28, 2025 at 1:34 PM David Haslam <[email protected]> wrote: >> >> Hi Fred, >> >> AFAICT, there's no LXX module under the language Κοινή Ἑλληνῐκή (/aka/ Ancient Greek) in the *eBible.org* repo. >> >> 1. What's the actual ModName of the one you tried to install? >> 2. Under which language did Xiphos list it? >> >> >> Best regards, >> >> David >> >> Sent with Proton Mail <https://proton.me/mail/home> secure email. >> >> On Friday, February 28th, 2025 at 6:01 PM, Fred <[email protected]> wrote: >>> Hmmm. after I choose the LXX module and click install there is a pause of 1 or 2 seconds but no progress bar. >>> it looks as if following Scott's directions above worked correctly... >>> see attached files. >>> >>> On Fri, Feb 28, 2025 at 12:06 PM David Haslam <[email protected]> wrote: >>> >>> I was also able to successfully install the *TNT* module*engtnteb*via HTTPS from eBible.org >>> >>> i.e. After adding the HTTPS module source to *Xiphos* as described in the thread. >>> >>> Best regards, >>> >>> David >>> >>> Sent with Proton Mail <https://proton.me/mail/home> secure email. >>> >>> On Friday, February 28th, 2025 at 4:06 PM, Fred <[email protected]> wrote: >>>> >>>> Scott, thanks for the recipe. I've done that and everything looks as if I did it right, but when I attempt to install a module from eBible nothing is installed, or not that I can find, not even by perusing the filesystem under ~/.sword. I ran Xiphos from the commandline and did it again, but no error messages appeared. >>>> >>>> Clues? (I have none!) >>>> >>>> Fred >>>> >>>> On Fri, Feb 28, 2025 at 9:06 AM David Haslam <[email protected]> wrote: >>>> >>>> _PostScript_: >>>> >>>> I was able to successfully install the YLT module *engylt1898eb* via HTTPS. >>>> >>>> So why the problem with the Brenton module? >>>> >>>> Best regards, >>>> >>>> David >>>> >>>> Sent with Proton Mail <https://proton.me/mail/home> secure email. >>>> >>>> On Friday, February 28th, 2025 at 1:47 PM, David Haslam <dfhdfh-g/[email protected]> wrote: >>>>> >>>>> I did that and then tried to install module *engBrent1851eb* >>>>> >>>>> *Xiphos* gave the error message "Install Failed" (just like it did for FTP). >>>>> >>>>> Best regards, >>>>> >>>>> David >>>>> >>>>> Sent with Proton Mail <https://proton.me/mail/home> secure email. >>>>> >>>>> >>>>> On Friday, February 28th, 2025 at 12:19 PM, Scott Buchanan scott-lwzoXI5syOZtdF/[email protected] wrote: >>>>> >>>>> On 27/02/2025 22:32, Fred wrote: >>>>> >>>>> As a Xiphos user, is there anything I can do to update my Xiphos to >>>>> use https? It seems to default to ftp. >>>>> >>>>> If you go to Edit > Module Manager > Module Sources > Add/Remove > >>>>> >>>>> Current Remote Sources > Add and use the following details >>>>> >>>>> Caption: eBible.org <http://eBible.org> HTTPS >>>>> Type: HTTPS >>>>> Host: ebible.org <http://ebible.org> >>>>> Directory: /sword >>>>> User: (leave blank) >>>>> Password: (leave blank) >>>>> >>>>> Then click Refresh on that page, you should now have the eBible.org <http://eBible.org> >>>>> HTTPS source added. Do the usual to access it as you would any other >>>>> Xiphos module source. >>>>> >>>>> I don't think there's an easy way to change all of the sources to HTTPS, >>>>> they must be added individually. I've opened a GitHub issue >>>>> (https://github.com/crosswire/xiphos/issues/1214) for this, updates will >>>>> be posted there and likely on the xiphos-devel mailing list too. >>>>> >>>>> -- >>>>> >>>>> Best regards, >>>>> Scott. >>>>> >>>>> _______________________________________________ >>>>> sword-devel mailing list: [email protected] >>>>> http://crosswire.org/mailman/listinfo/sword-devel >>>>> Instructions to unsubscribe/change your settings at above page >>>>> >>>> >>>> _______________________________________________ >>>> sword-devel mailing list: [email protected] >>>> http://crosswire.org/mailman/listinfo/sword-devel >>>> Instructions to unsubscribe/change your settings at above page >>>> >>> >>> _______________________________________________ >>> sword-devel mailing list: [email protected] >>> http://crosswire.org/mailman/listinfo/sword-devel >>> Instructions to unsubscribe/change your settings at above page >>> >> >> _______________________________________________ >> sword-devel mailing list: [email protected] >> http://crosswire.org/mailman/listinfo/sword-devel >> Instructions to unsubscribe/change your settings at above page >> > _______________________________________________ sword-devel mailing list: [email protected] http://crosswire.org/mailman/listinfo/sword-devel Instructions to unsubscribe/change your settings at above page