RE: Booting error of L4Linux enabled SMP surpport

Hi,
I have a low-level mistake. The panic is not relate to SMP. 
Before I use x86-mp_vPCI_defconfig as smp config file, I use x86-native_defconfig as unicore config file.
x86-mp_vPCI_defconfig do not enable CONFIG_EXT2 _FS, only enable CONFIG_EXT3_FS, and x86-native_defconfig also do not enable CONFIG_EXT2 _FS , but it enable CONFIG_EXT4_FS.

When loading ramdisk(EXT2 FILE SYSTEM), L4Linux which use x86-mp_vPCI_defconfig do not find the ramdisk, so kernel panic happened. When i enable CONFIG_EXT4_FS, it is OK.

Stephen

-----Original Message-----
From: Matthias Lange [mailto:[email protected]] 
Sent: 2015年5月29日 14:55
To: [email protected]
Cc: Xiefeng (Stephen)
Subject: Re: Booting error of L4Linux enabled SMP surpport

Hi,

On 05/28/2015 11:36 AM, Xiefeng (Stephen) wrote:
> Hi Adam,
> 
> Thank you for your prompt. I have found the panic reason.

Would you mind sharing the reason and of course the solution with the community?

Thanks,
Matthias.

> 
> Stephen
> 
> -----Original Message-----
> From: l4-hackers [mailto:[email protected]] On 
> Behalf Of Adam Lackorzynski
> Sent: 2015年5月27日 6:35
> To: [email protected]
> Subject: Re: Booting error of L4Linux enabled SMP surpport
> 
> On Fri May 22, 2015 at 07:49:14 +0000, Xiefeng (Stephen) wrote:
>> Hi all,
>>
>> I use entry L4Linux-mag-x86 in modules.list to start a L4Linux on L4Re successfully. The codes is l4re-snapshot-2014092821.
>> L4Linux use x86-native_deconfig complie, use l4lx-gfx.cfg to start L4Linux. This config is just set one cpu for L4Linux.
>>
>> If I set l4x_cpus=2 in l4lx-gfx.cfg, use x86-mp_vPCI_defconfig and 
>> set
>> CONFIG_NR_CPUS=2 to compile the L4Linux, when I start L4Linux, a kernel panic happened:
>>
>> l4linux | Loading: rom/ramdisk-x86.rd l4linux | INITRD: Size of 
>> RAMdisk is 3072KiB l4linux | RAMdisk from
>> 88d70000 to 89070000 [3072KiB] l4linux | rtc not found l4linux |
>> l4lx_thread_create: Created thread 41f (timer0) (u:b3000a00, 
>> v:00000000, sp:008e1fa8) l4linux | WARNING: Unknown wrmsr: 0000008b 
>> at 0x414bad l4linux | WARNING: Unknown rdmsr: 00000186 at 0x85e1d6 
>> l4linux | WARNING: Unknown rdmsr: 00000187 at 0x85e1d6 l4linux |
>> WARNING: Unknown wrmsr: 000000c1 at 0x85e2a7 l4linux | Launching cpu1 
>> on pcpu 1 at 0x4024e0 l4linux | l4lx_thread_create: Created thread 
>> 420
>> (cpu1) (u:b3000800, v:b3000600, sp:008c7fa8) l4linux | WARNING: 
>> Unknown wrmsr: 0000008b at 0x414bad l4linux | l4lx_thread_create: 
>> Created thread 424 (timer1) (u:b3000400, v:00000000, sp:008e3fa8) 
>> l4linux | Spurious IPI on CPU0: 4 l4linux | panic: going to sleep 
>> forever, bye
> 
> Is there any output in the framebuffer window?
> Anyway, change the  console=tty0 parameter in l4lx-gfx.cfg to
> console=ttyLv0 and also add earlyprintk=1 (plus make sure that CONFIG_EARLY_PRINTK is enabled). Then run again.
> 
> 
> 
> Adam
> 


--
Matthias Lange, [email protected], +49 - 351 - 41 88 86 14

Kernkonzept GmbH.  Sitz: Dresden.  Amtsgericht Dresden, HRB 31129.
Geschäftsführer: Dr.-Ing. Michael Hohmuth

_______________________________________________
l4-hackers mailing list
[email protected]
http://os.inf.tu-dresden.de/mailman/listinfo/l4-hackers