Re: [mh] Adding Tasmota HTTP support

Steve,

Gaah, I just realized I never answered your question about scenes.  I 
never use "scenes" built into devices, instead I just write MH code to 
do what I want.  But if you really wanted to, yes, you can make Tasmota 
do that.

Jeff


On 2020-12-14 8:23 p.m., Stephen Switzer wrote:
> This is GREAT news! Good job on the code! Those pesky firewalls can 
> cause havoc, can't they? LOL
>
> I have a bunch of Insteon devices that I've come to like, but there's 
> a couple little oddities with 1-2 of the devices that often don't 
> communicate and never synchronize with the PLM, even though 3 other 
> devices in the same wall box do!??
>
> The one question that I have for you on these devices is can I set up 
> keypad buttons to control multiple devices on one wall plate like the 
> 8 key KPL? Oh, and one more question... can they respond to "scenes"? 
> For example, I have one button that turns off all 1st floor devices 
> for bedtime. All lights and fans are off at once.
>
> Thanks! Looking forward to more progress.
>
> Steve
>
> On Mon, Dec 14, 2020 at 6:16 PM Jeff Siddall via misterhouse-users 
> <[email protected] 
> <mailto:[email protected]>> wrote:
>
>     Another update: yay, everything is working!
>
>     There isn't much to screenshot here (I mean, they just look like any
>     other type of thing in MH) but there are a couple of log
>     messages.  When
>     MH starts you get:
>
>     [Tasmota_HTTP::Switch] Created item with address 192.168.1.128
>
>     And if debug=tasmota is set in your mh.private.ini then you also get
>     this when MH turns a device on remotely:
>
>     [Tasmota_HTTP::Item] DEBUG: Set $Outdoor_Lights_SM state to on
>     [Tasmota_HTTP::Item] DEBUG: Received ack from $Outdoor_Lights_SM
>     (192.168.1.128)
>
>     or if you control the Tasmota device locally you get:
>
>     [Tasmota_HTTP::Item] DEBUG: Received set state to off from
>     $Outdoor_Lights_SM (192.168.1.128)
>
>     On the Tasmota, after setting it up as the right template, it only
>     takes
>     a couple of console commands to get the local control messages
>     sent out
>     over HTTP:
>
>     Rule1 ON Power1#State DO WebSend [<mh_address>:<mh_port>]
>     /SET;none?select_item=<item_name>&select_state=%value% ENDON
>     Rule1 1
>     SwitchMode 3
>
>     Where: <item_name> is the name of this device in MH (ex:
>     Outdoor_Lights_SM), <mh_address> is the IP address of MH, and
>     mh_port is
>     the TCP port that the MH web server is listening on.
>
>     SwitchMode 3 just sets the switch input to work like any other
>     typical
>     home automation switch where each push of the momentary button
>     toggles
>     the state.
>
>     The issue I had with the Tasmota sending local control messages was
>     because I hadn't put a hole through the firewall to allow that.  My
>     phone did work, but that is because it was going through a proxy.
>
>     After I got two-way communication working I rewrote the module a
>     bit to
>     add ack tracking and to use an inherited classes for different
>     devices,
>     which should make it easy for people to add more Tasmota things
>     down the
>     road.  Right now there is only a Tasmota_HTTP::Switch (with on and
>     off
>     states), but hopefully that will cover the most common use case.  All
>     this added another 18 lines of code, so yeah, it still doesn't do
>     error
>     checking or other things it probably should.
>
>     I also created a bash script to install Tasmota on Sonoff 3.1.5 (OTA)
>     devices, and will post that separately.  One nice thing about these
>     devices is that they requires no special apps or utilities to
>     setup.  I
>     did mine using a browser on my phone and curl on my MH machine.  I
>     also
>     used apache to server the firmware, but I think I could have just
>     pointed them to the Tasmota OTA server if I wanted.
>
>     I will work on creating a pull request for the module and post an
>     update
>     if/when I have success with git.
>
>     Jeff
>
>     On 2020-12-13 11:43 p.m., Jeff Siddall via misterhouse-users wrote:
>     > Update: some Sonoff Minis showed up this afternoon.  It was a bit
>     > fiddly to get them updated to Tasmota, but I have that done now.
>     More
>     > surprisingly, I also successfully controlled them from my new perl
>     > module on the first attempt.  I don't remember the last time I
>     wrote
>     > something that worked on the first try!
>     >
>     > Unfortunately I have had less luck getting Tasmota to send local
>     > control messages back to MH.  It always reports a timeout when
>     sending
>     > the HTTP request, even though I can successfully send the exact
>     same
>     > URL from my phone on the same WiFi network.  If I take out the port
>     > number from the URL then the Tasmota device does successfully
>     send the
>     > request [to port 80], but I have an apache server running on
>     port 80
>     > on my MH machine so that doesn't exactly work.  I hope I haven't
>     found
>     > a bug in the firmware.
>     >
>     > I will do some more troubleshooting to see if I can get to the
>     bottom
>     > of it.
>     >
>     > Jeff
>     >
>     > On 2020-12-13 12:45 a.m., Jeff Siddall wrote:
>     >> Thanks!
>     >>
>     >> I decided to take a stab at it, and after a couple of hours have
>     >> Tasmota_HTTP_Item.pm written.  This one is a more substantial 30
>     >> lines of code, plus another 5 lines in read_table_A.pl.
>     >>
>     >> Now I just need some devices to test it with.
>     >>
>     >> Jeff
>     >>
>     >> On 2020-12-12 9:55 p.m., H Plato wrote:
>     >>> Look at my razberry module. This is very similar to how it works.
>     >>> Sending a http command for control and having a web endpoint for
>     >>> accepting status changes.
>     >>>
>     >>> Sent from my mobile device.
>     >>>
>     >>>> On Dec 12, 2020, at 7:41 PM, Jeff Siddall via misterhouse-users
>     >>>> <[email protected]
>     <mailto:[email protected]>> wrote:
>     >>>>
>     >>>> As a follow-on to the "What’s better than Insteon?" thread,
>     Giles
>     >>>> put me onto the Tasmota open source firmware that will run on a
>     >>>> huge number (literally thousands) of smart things on the market.
>     >>>> While you can talk to those over MQTT, then you also need to
>     setup
>     >>>> a broker, and that seems awkward in a world where all the smart
>     >>>> things have web interfaces.
>     >>>>
>     >>>> So that got me thinking about building a "Tasmota_HTTP_Item" in
>     >>>> MH.  There is already support for SETting things in MH using
>     HTTP
>     >>>> via the lib/http_server.pl <http://http_server.pl> code. 
>     Tasmota devices can send updates
>     >>>> using HTTP, as in this example:
>     >>>>
>     >>>>
>     https://tasmota.github.io/docs/Rules/#two-way-light-switches-without-mqtt
>
>     >>>>
>     >>>>
>     >>>> So combining those two would result in a rule for local switch
>     >>>> control on the Tasmota with a command like:
>     >>>>
>     >>>> WebSend [<mh_ip_address>:8081]
>     >>>> /SET;none?select_item=Tasmota_Item_Name&select_state=on
>     >>>>
>     >>>> And for remote control, MH would send a command like this
>     when an
>     >>>> item is set:
>     >>>>
>     >>>> get 'http://<tasmota_item_ip>/cm?cmnd=POWER1 ON'
>     >>>>
>     >>>> The only other thing is that the "set" function for the
>     >>>> Tasmota_Item would need to check if the item was set_by:
>     >>>>
>     >>>> web [<tasmota_item_ip_address>]
>     >>>>
>     >>>> ...and then not send anything in that case so it doesn't end
>     up in
>     >>>> a send loop with the Tasmota device.
>     >>>>
>     >>>> Anyone tried anything like that?  If not, I guess it is time to
>     >>>> order some of these things and start tinkering!
>     >>>>
>     >>>>
>     >>>>
>     >>>> ________________________________________________________
>     >>>> To unsubscribe from this list, go to:
>     >>>> https://lists.sourceforge.net/lists/listinfo/misterhouse-users
>     >>>>
>     >
>     >
>     > ________________________________________________________
>     > To unsubscribe from this list, go to:
>     > https://lists.sourceforge.net/lists/listinfo/misterhouse-users
>     >
>
>
>     ________________________________________________________
>     To unsubscribe from this list, go to:
>     https://lists.sourceforge.net/lists/listinfo/misterhouse-users
>
>
>
> -- 
> Best regards,
> Steve Switzer
>
> ---
> Get world-class business I.T. services and a phone system with awesome features that won't challenge your budget!
> http://www.sbsROC.com
>
>
> ________________________________________________________
> To unsubscribe from this list, go to:https://lists.sourceforge.net/lists/listinfo/misterhouse-users
>

________________________________________________________
To unsubscribe from this list, go to: https://lists.sourceforge.net/lists/listinfo/misterhouse-users