Re: [mh] Whole home power monitoring

I’m trying to understand amps, so I know I have 2 120v phases and can read the kW, so I should be able to get amps right?

> On May 23, 2021, at 9:56 AM, Spencer Ryan <[email protected]> wrote:
> 
> Since voltage is constantly changing you need to know both amperage and voltage for accurate power usage measurement
> 
> On Sun, May 23, 2021, 11:51 AM H Plato <[email protected] <mailto:[email protected]>> wrote:
> Thanks everyone for the suggestions!
> 
> I was thinking about those clips, but I’m mostly interested in overall usage, and I don’t know if I’d need 2 power monitoring off the 100a service, one for each phase.
> 
> I had RTL-SDR almost working a few years back sending data to MH through MQTT. The RTL-SDR process had a memory leak so it would make the rpi unresponsive, but I was able to read my outside electrical meter. I’m going to dust that off and maybe reboot the rpi every night to address the memory leak.
> 
> https://hackaday.com/2017/12/21/read-home-power-meters-with-rtl-sdr/ <https://hackaday.com/2017/12/21/read-home-power-meters-with-rtl-sdr/>
> 
> So stupid question — how would one convert kW to Amps. I’m on a 60hz/120v service, but since there are 2 phases coming into the house, should it be the meter kW / 240 or kW / 120?  I think it’s 240, but I’m not sure.
> 
> > On May 23, 2021, at 9:32 AM, Eloy Paris <[email protected] <mailto:[email protected]>> wrote:
> > 
> > Hi Howard,
> > 
> > Have you seen Marc's blog posts on this topic? The latest seems to be
> > this one:
> > 
> > http://marc.merlins.org/perso/linuxha/post_2010-08-13_Fine-grained-house-wide-power-monitoring-with-Brultech-ECM1240_-ecmread_py-_with-net-metering-support_-and-graphing-with-cacti.html <http://marc.merlins.org/perso/linuxha/post_2010-08-13_Fine-grained-house-wide-power-monitoring-with-Brultech-ECM1240_-ecmread_py-_with-net-metering-support_-and-graphing-with-cacti.html>
> > 
> > A decade old but I'd still take a look there as a starting point, see
> > what the equivalent products today are, e.g. the Brultech Greeneye, etc.
> > Good pointers and experiences that Marc shares there. And Cacti would
> > probably still be in the picture, of course.
> > 
> > Cheers,
> > 
> > Eloy Paris.-
> > 
> > On Sun, May 23, 2021 at 08:41:28AM -0600, H Plato wrote:
> > 
> >> Has anyone found any good DIY power monitoring solutions? My panel is full and I’d to get an idea of the average and peak load. I have a 100a service, and the wiring from the utility isn’t sized for 200a, so an upgrade would be pretty expensive. I’m hoping that the usage is low enough that I can just replace the panel without upgrading the service, so having usage tracking would be really helpful.
> >> 
> >> ________________________________________________________
> >> To unsubscribe from this list, go to: https://lists.sourceforge.net/lists/listinfo/misterhouse-users <https://lists.sourceforge.net/lists/listinfo/misterhouse-users>
> >> 
> 
> 
> 
> ________________________________________________________
> To unsubscribe from this list, go to: https://lists.sourceforge.net/lists/listinfo/misterhouse-users <https://lists.sourceforge.net/lists/listinfo/misterhouse-users>
>

________________________________________________________
To unsubscribe from this list, go to: https://lists.sourceforge.net/lists/listinfo/misterhouse-users