Re: [mh] Schulter Ditra thermostats

I have the Schluter code running, but frankly I don't know how to use 
it.  I set the required params, and I can see it authenticating and 
fetching my group.  I tried creating a temp object, but I don't know how 
to read it.

$Basement_Bathroom_Thermostat = new Schulter_Ditra();
$Basement_Bathroom_temp = new 
Ditra_thermostat_temp($Basement_Bathroom_Thermostat,"SERIAL NUMBER");

Can you provide any guidance?

Thanks,
Tom

On 2021-11-04 17:20, Tom MacLean wrote:
> Is it all contained in lib/Schulter_Ditra.pm  ?   (BTW, it's Schluter.)
> 
> Will this lib run on the current release or are there unmet
> dependencies?  In any case, i will try.
> 
> Cheers
> 
> On 2021-11-03 22:49, H Plato wrote:
>> That’s good. I uploaded my latest module to github. It tracks mode,
>> and you can change the setpoint and pull the temperature. Be good to
>> know if you have any feedback.
>> 
>>> On Nov 3, 2021, at 8:35 PM, Tom MacLean <[email protected]> wrote:
>>> 
>>> It took me a little fighting to get Crypt::SSLeay installed, but I 
>>> got there. (cpan wouldn't do it, I had to apt-get the relevant 
>>> libraries.)
>>> 
>>> I am able to authenticate at the schluter URL as well as the generic 
>>> one.  I checked and both domains map to the same IP address.
>>> 
>>> On 2021-11-02 10:52, H Plato wrote:
>>>> Interesting. I can authenticate against that URL as well, so I bet
>>>> you’re correct that the reseller is branding that URL.
>>>> To create an account, I had to have power to my wifi device, and 
>>>> then
>>>> associated that device with an email account.
>>>> I don’t have any documentation — I pulled the endpoints 
>>>> from other
>>>> integrations that are out there on github.
>>>>> On Nov 1, 2021, at 9:17 PM, Tom MacLean <[email protected]> 
>>>>> wrote:
>>>>> In truth, I haven't hooked up my unit to wifi yet -- the relevant 
>>>>> bathroom is still under construction (by me), but I'm almost done.  
>>>>> The heated floor and thermostat are in, all I need is the "round 
>>>>> tuit" to connect it to wifi.
>>>>> The URL I have is diferrent, but the Schluter Thermostat is 
>>>>> definitely an OJ Microline ... so I think they have branded URLs or 
>>>>> perhaps a different application number.  The code I expect to use 
>>>>> uses:
>>>>> https://mythermostat.info/api/authenticate/user
>>>>> {"Email":"LOGIN EMAIL","Password":"LOGIN PASSWORD","Application":0}
>>>>> Looks familiar, no?
>>>>> Do you have documentation? The only two actions I know about are 
>>>>> setting an override "away" temperature, and resuming the normal 
>>>>> schedule.
>>>>> Cheers
>>>>> Tom
>>>>> On 2021-10-31 18:25, H Plato wrote:
>>>>>> OK, if you have an account with one of those stats, try running 
>>>>>> this
>>>>>> command to see if you get a sessionID:
>>>>>> ./get_url -response_code -json -post
>>>>>> '{"Email”:”[email protected]","Password”:"password","Application":"7"}'
>>>>>> https://ditra-heat-e-wifi.schluter.com/api/authenticate/user
>>>>>> If you get back something like this:
>>>>>> RESPONSECODE:200
>>>>>> {"SessionId”:”sdfhsdihflasdfhalsdiufha","NewAccount":false,"ErrorCode":0,"RoleType":3000,"Email":"[email protected]","Language":”EN"}
>>>>>> Then it will work.
>>>>>>> On Oct 31, 2021, at 4:12 PM, Tom MacLean <[email protected]> 
>>>>>>> wrote:
>>>>>>> Hi
>>>>>>> Is the Schluter thermostat one of the models made by OJ 
>>>>>>> Electronics?  They make thermostats for a bunch of floor heating 
>>>>>>> companies, including also WarmlyYours. In short, I could test it 
>>>>>>> if is.   I didn’t think they had a public API. All I 
>>>>>>> found was a rather limited NodeRED script.
>>>>>>> Cheers,
>>>>>>> Tom
>>>>>>> Sent from my iPhone
>>>>>>>> On Oct 30, 2021, at 2:34 PM, H Plato <[email protected]> wrote:
>>>>>>>> I don’t know if anyone else has any of 
>>>>>>>> these, but I’m just putting the finishing touches on 
>>>>>>>> a MH module to poll and control the wifi in-floor heat 
>>>>>>>> thermostats.
>>>>>>>> It feels like there are a bunch of changes out there (like the 
>>>>>>>> tasmota stuff), I’m wondering if it makes sense to 
>>>>>>>> combine them all into master and look to package it for a 
>>>>>>>> release. MH is pretty mature and stable, so there 
>>>>>>>> hasn’t been updates in a while, but would be good to 
>>>>>>>> have a current download.
>>>>>>>> ________________________________________________________
>>>>>>>> To unsubscribe from this list, go to: 
>>>>>>>> https://lists.sourceforge.net/lists/listinfo/misterhouse-users
>>>>>>> ________________________________________________________
>>>>>>> To unsubscribe from this list, go to: 
>>>>>>> https://lists.sourceforge.net/lists/listinfo/misterhouse-users
>>> 
>>> 
>>> ________________________________________________________
>>> To unsubscribe from this list, go to: 
>>> https://lists.sourceforge.net/lists/listinfo/misterhouse-users
>>> 
> 
> 
> ________________________________________________________
> To unsubscribe from this list, go to:
> https://lists.sourceforge.net/lists/listinfo/misterhouse-users


________________________________________________________
To unsubscribe from this list, go to: https://lists.sourceforge.net/lists/listinfo/misterhouse-users