Re: [mh] Need a working Z-Wave configuration

Great! Would you please share the Razberry configuration that you use? I 
just need to see the *.ini  entries and one or two sample *.mht entries, 
comparable to mine below, so I can see if I missed  or messed up anything.

Also, if you have your RPi in a case, what case do you use that 
accommodates the razberry module?

                              -Brian M.

On 12/11/22 07:58, H Plato wrote:
> Hi Brian, I have a working Z-wave setup, but not using the AEOTec 
> Z-Stick. I have a razberry board plugged into the raspberry pi, and 
> use webcalls back and forth. (There’s a razberry module in MH) 
> Reliability is on-par with insteon for me. I control around 15 items, 
> mainly blinds, locks and a few outdoor modules.
>
>> On Dec 10, 2022, at 10:26 AM, Brian M 
>> <[email protected]> wrote:
>>
>> I'm hoping someone with a working Z-Wave configuration under MH will 
>> share their relevant configuration information with me, as I can't 
>> get mine to work.
>>
>> Details:
>>
>> I'm starting to dabble with Z-Wave under MH. I have an AEOTec Z-Stick 
>> (Gen5) plugged into my Raspberry Pi. I've tested the Z-stick using 
>> the Open Z-Wave control panel (ozwcp) installed and executed under 
>> the MH login. It can control my one Z-Wave light switch, so I know 
>> the Z-stick is good and the MH login has all the necessary permissions.
>>
>> MH can't seem to connect to the Z-stick however. At start-up it 
>> attempts to send a reset to the Z-Stick, but fails.
>>
>> I'm running the latest MH code pulled from the master branch (last 
>> update 10/29/2022).
>>
>> In mh.private.ini I have:
>>
>>     ZWave_RZC0P_serial_port=/dev/ttyACM0
>>     rzc0p_errata=4
>>     rzc0p_retry_limit=5
>>     rzc0p_update10=0
>>     rzc0p_update100=1
>>     rzc0p_update1000=1
>>     rzc0p_timeout=10                      # Tried this at 60, no
>>     difference.
>>     rzc0p_id=001
>>
>> In items.mht I have:
>>
>>     #Item Type              Zwave ID# name            groups         
>>     interface polling_interval        2way(1 or 0)    resume_level
>>     (if dimmer)
>>     ZWAVE_APPLIANCE,        006, office_fan,     All_Lights,    
>>     ZWave_RZC0P, 7,                      0
>>
>> Here's the log:
>>
>>     12/10/22 09:15:52 AM ZWave_RZC0P Info: Specified retry_limit of 5
>>     12/10/22 09:15:52 AM ZWave_RZC0P Info: Specified timeout of 10
>>     seconds
>>      to Zwave interfaceM ZWave_RZC0P Debug: Writing data >DE
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: ZWave
>>     interface timeout, cmd:>DE
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: data timeout
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: cmd timeout
>>     12/10/22 09:15:52 AM Oops1: Use of uninitialized value in hash
>>     element at /home/mh/mh/bin/../lib/ZWave_RZC0P.pm line 420.
>>     12/10/22 09:15:52 AM Oops1: Use of uninitialized value $upd_count
>>     in numeric gt (>) at /home/mh/mh/bin/../lib/ZWave_RZC0P.pm line 423.
>>     12/10/22 09:15:52 AM Oops1: Use of uninitialized value in hash
>>     element at /home/mh/mh/bin/../lib/ZWave_RZC0P.pm line 429.
>>     12/10/22 09:15:52 AM Oops1: Use of uninitialized value in numeric
>>     gt (>) at /home/mh/mh/bin/../lib/ZWave_RZC0P.pm line 429.
>>     12/10/22 09:15:52 AM ZWave_RZC0P Adding
>>     id:006,type:ZWAVE_APPLIANCE,inst:0 to node list
>>     12/10/22 09:15:52 AM ZWave_RZC0P Debug: Writing data >?N006 to
>>     Zwave interface
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: ZWave
>>     interface timeout, cmd:>?N006
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: data timeout
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: xmit timeout
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: cmd timeout
>>     12/10/22 09:15:52 AM ZWave_RZC0P Info: Retrying Command >?N006,
>>     Retry Number:1 time:1670692573.43541
>>     12/10/22 09:15:52 AM ZWave_RZC0P Debug: Writing data >?N006 to
>>     Zwave interface
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: ZWave
>>     interface timeout, cmd:>?N006
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: data timeout
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: xmit timeout
>>     12/10/22 09:15:52 AM ZWave_RZC0P ZWave_RZC0P error: cmd timeout
>>     12/10/22 09:15:52 AM ZWave_RZC0P Was in Zwave check_for_data sub
>>     for 10.0004432201385 seconds
>>
>> The Oops1 errors are in the timeout handler, so they probably 
>> wouldn't happen if the timeout didn't occur. The simple problem is 
>> that the initial send is timing out.
>>
>> It's probably something simple, like needing to declare a baud rate 
>> (which baud and how) or something similar. Do I need to run setserial 
>> first? Can anyone put me on the right track?
>>
>> -Brian M
>>
>>
>> ________________________________________________________
>> To unsubscribe from this list, go to: 
>> https://lists.sourceforge.net/lists/listinfo/misterhouse-users
>>
>

________________________________________________________
To unsubscribe from this list, go to: https://lists.sourceforge.net/lists/listinfo/misterhouse-users