Re: SMS routing based on smsc-id does not work properly.

Hi Roman,

Are you on cvs HEAD or any particular release?

Cheers,
Alan

On Mon, 2004-11-29 at 22:26 +0300, Roman wrote:
> Dear, Sirs!
> 
> 
> I have two different SMSC(one is SMPP-based, another one is HTTP-based ) in configuration file and have some problems with
> routing. I want to route reply to the same SMSC, which receive
> request. I make configuration as in documentation
> http://www.kannel.org/download/kannel-userguide-snapshot/userguide.html#AEN4033
> but it does not work properly.
> 
> CONFIG:
> 
> group = core
> admin-port = XXXX
> smsbox-port = XXXX
> log-file = "kannel.log"
> log-level = 0
> box-deny-ip = "*.*.*.*"
> box-allow-ip = "127.0.0.1"
> access-log = "access.log"
> store-file = "kannel.store"
> 
> 
> # SMSC CONNECTIONS
> 
> group = smsc
> smsc = smpp
> smsc-id = SMSC1
> denied-smsc-id = SMSC2
> transceiver-mode = 1
> host = SMPP SMSC IP Addr
> port = XXXX
> smsc-username = "user"
> smsc-password = "pass"
> system-type = "VMA"
> 
> 
> group = smsc
> smsc = http
> smsc-id = SMSC2
> denied-smsc-id = SMSC1
> system-type = kannel
> smsc-username = "user"
> smsc-password = "pass"
> port = XXXX
> send-url = "http://XXX.XXX.XX/sms"
> connect-allow-ip = "HTTP SMSC IP"
> 
> 
> # SMSBOX SETUP
> 
> group = smsbox
> bearerbox-host = localhost
> sendsms-chars = "0123456789 +-"
> log-file = "smsbox.log"
> log-level = 0
> access-log = "access.log"
> 
> group = sms-service
> keyword = default
> name = "test1"
> max-messages = 10
> concatenation = false
> allowed-receiver-prefix = 1111
> accepted-smsc = SMSC1
> split-chars = " "
> omit-empty = true
> text = "TEST1"
> 
> group = sms-service
> keyword = default
> name = "test2"
> max-messages = 10
> concatenation = false
> allowed-receiver-prefix = 2222
> accepted-smsc = SMSC2
> split-chars = " "
> omit-empty = true
> text = "TEST2"
> 
> If I send sms request from SMSC1, kannel send reply back via SMSC2, but if i send
> sms request from SMSC2, kannel sends reply back via SMSC2 too.
> Then i set config block of SMSC2 above SMSC1. And if I send sms
> request from SMSC1, kannel sends reply back via SMSC1, but if i send
> sms request from SMSC2 kannel send reply back via SMSC1 too.
> 
> Only if i set routing based on "allowed-prefix" in my config, then all
> work fine. But kannel users guide shows than i can do routing based on
> "smsc-id, denied-smsc-id, accepted-smsc" params.
> 
> What i do wrong?
> 
> Thank you beforehand.
> 
> 
-- 
Alan McNatty <[email protected]>
-- 
Alan McNatty <[email protected]>