bearer box error

I am trying to use Nokia 1600 as smsc.I have connected it to USB port using 
dlr-5 cable. 
---------------------------------------------------------------------------- 
when I give dmesg | grep usb coomand,following is the output. 

usb.c: registered new driver usbdevfs 
usb.c: registered new driver hub 
usb.c: new USB bus registered, assigned bus number 1 
usb-uhci.c: $Revision: 1.275 $ time 17:59:01 Mar 13 2003 
usb-uhci.c: High bandwidth mode enabled 
usb-uhci.c: USB UHCI at I/O 0xe400, IRQ 10 
usb-uhci.c: Detected 2 ports 
usb.c: new USB bus registered, assigned bus number 2 
usb-uhci.c: USB UHCI at I/O 0xe800, IRQ 11 
usb-uhci.c: Detected 2 ports 
usb.c: new USB bus registered, assigned bus number 3 
usb-uhci.c: USB UHCI at I/O 0xec00, IRQ 10 
usb-uhci.c: Detected 2 ports 
usb.c: new USB bus registered, assigned bus number 4 
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver 
usb.c: registered new driver hiddev 
usb.c: registered new driver hid 
usb.c: USB device 2 (vend/prod 0x67b/0x2303) is not claimed by any active 
driver 
. 
usb.c: registered new driver serial 
usbserial.c: USB Serial support registered for Generic 
usbserial.c: USB Serial Driver core v1.4 
usbserial.c: USB Serial support registered for PL-2303 
usbserial.c: PL-2303 converter detected 
usbserial.c: PL-2303 converter now attached to ttyUSB0 (or usb/tts/0 for 
devfs) 
usb-uhci.c: interrupt, status 2, frame# 1483 
usb_control/bulk_msg: timeout 
usb_control/bulk_msg: timeout 
----------------------------------------------------------------------------- 
A part of my config file is as follows, 

group = smsc 
smsc = at 
smsc-id = 1600@ttyUSB0 
modemtype = nokiaphone 
device=/dev/ttyUSB0 
speed = 19200 
pin = 89914500040057921576 

group = modems 
id = nokiaphone 
name = "Nokia Phone" 
detect-string = "Nokia Mobile Phone" 
need-sleep = true 
keepalive-cmd = "AT+CBC;+CSQ" 
enable-mms = false 
-------------------------------------------------------------------------- 
When I try to run the bearer box,I get the following error, 

2006-03-20 09:38:05 [4336] [0] INFO: Debug_lvl = 1, log_file = <none>,
log_lvl 
= 
 0 
2006-03-20 09:38:05 [4336] [0] WARNING: DLR: using default 'internal' for 
storag 
e type. 
2006-03-20 09:38:05 [4336] [0] INFO: DLR using storage type: internal 
2006-03-20 09:38:05 [4336] [0] INFO: HTTP: Opening server at port 13000. 
2006-03-20 09:38:05 [4336] [0] INFO: BOXC: 'smsbox-max-pending' not set,
using 
d 
efault (100). 
2006-03-20 09:38:05 [4336] [0] INFO: DLR rerouting for smsc id <FAKE> 
disabled. 
2006-03-20 09:38:05 [4336] [0] INFO: DLR rerouting for smsc id
<1600@ttyUSB0> 
di 
sabled. 
2006-03-20 09:38:05 [4336] [0] INFO: AT2[1600@ttyUSB0]: configuration shows 
mode 
mtype <nokiaphone> 
2006-03-20 09:38:05 [4336] [0] INFO: AT2[1600@ttyUSB0]: read modem
definition 
fo 
r <Nokia Phone> 
2006-03-20 09:38:05 [4336] [0] INFO:
---------------------------------------- 
2006-03-20 09:38:05 [4336] [0] INFO: Kannel bearerbox II version 1.4.0 
starting 
2006-03-20 09:38:05 [4336] [0] INFO: MAIN: Start-up done, entering mainloop 
2006-03-20 09:38:05 [4336] [7] INFO: AT2[1600@ttyUSB0]: opening device 
2006-03-20 09:38:10 [4336] [7] INFO: AT2[1600@ttyUSB0]: init device 
2006-03-20 09:38:12 [4336] [7] INFO: AT2[1600@ttyUSB0]: speed set to 19200 
2006-03-20 09:38:17 [4336] [7] ERROR: AT2[1600@ttyUSB0]: Opening failed. 
Termina 
ting 
------------------------------------------------------------------------------ 
The last few lines keep repeating. 
Can anyone help me here? 

Regards, 
Rashmi. 

--
View this message in context: http://www.nabble.com/bearer-box-error-t1309265.html#a3488211
Sent from the Kannel - Dev forum at Nabble.com.