Re: PIL 1.1.7 binary for python 2.4
Jack Uretsky <[email protected]>
| Newsgroups | gmane.comp.python.image |
|---|---|
| Message-ID | <[email protected]> |
Yes and no. In addition to the version that came with Snow Leopard, I downloaded version 3.1.1 Regards, Jack "Trust me. I have a lot of experience at this." General Custer's unremembered message to his men, just before leading them into the Little Big Horn Valley On Sun, 15 Nov 2009, Bill Janssen wrote: > So, did you download and install a different Python than came with your > Mac? > > Bill > > > Jack Uretsky <[email protected]> wrote: > >> Thanks. I'n not seeing why that helps. I did Finder-File-Find-SDK >> and got 156 items. Im not sure what to do next >> Regards, >> Jack >> >> "Trust me. I have a lot of experience at this." >> General Custer's unremembered message to his men, >> just before leading them into the Little Big Horn Valley >> >> >> >> >> On Sat, 14 Nov 2009, Bill Janssen wrote: >> >>> OK, and is that Python 2.6 the one that comes with Snow Leopard? >>> >>> That should pin it down. The question here is, why is your system >>> trying to use the 10.4 SDK, instead of the 10.6 SDK? The only thing I >>> can think of is that you are using a non-Apple-supplied Python, which >>> was built against the 10.4 SDK, so it's trying to use that to build PIL, >>> too. >>> >>> Bill >>> >>> >>> Jack Uretsky <[email protected]> wrote: >>> >>>> Hi- >>>> Xcode - 3.2 (bundled with Mac OS upgrade software) >>>> Python 2.6 >>>> Mac OS X 10.6.1 (Snow Leopard) >>>> >>>> "Trust me. I have a lot of experience at this." >>>> General Custer's unremembered message to his men, >>>> just before leading them into the Little Big Horn Valley >>>> >>>> >>>> >>>> >>>> On Fri, 13 Nov 2009, Bill Janssen wrote: >>>> >>>>> Need more details. What version of OS X, what version of Python, what >>>>> version of Xcode? >>>>> >>>>> Bill >>>>> >>>>> Jack Uretsky <[email protected]> wrote: >>>>> >>>>>> Hi- >>>>>> Perhaps you can answer, at least, the second question. In >>>>>> what file do I find the gcc? >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>> 1. What is my Xcode problem? When I run >python2.6 setup.py build >>>>>> I get: running build >>>>>> running build_py >>>>>> running build_ext >>>>>> --- using frameworks at /System/Library/Frameworks >>>>>> building '_imaging' extension >>>>>> Compiling with an SDK that doesn't seem to exist: >>>>>> /Developer/SDKs/MacOSX10.4u.sdk >>>>>> Please check your Xcode installation >>>>>> >>>>>> 2. this is followed by the line >>>>>> >>>>>> gcc -arch ppc -arch i386 -isysroot /Developer/SDKs/MacOSX10.4u.sdk >>>>>> -fno-strict-aliasing -fno-common -dynamic -DNDEBUG -g -O3 -DHAVE_LIBZ - >>>>>> >>>>>> In what file do I find this line so I can make the recommended correction? >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> "Trust me. I have a lot of experience at this." >>>>>> General Custer's unremembered message to his men, >>>>>> just before leading them into the Little Big Horn Valley >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> _______________________________________________ >>>>>> Image-SIG maillist - [email protected] >>>>>> http://mail.python.org/mailman/listinfo/image-sig >>>>> >>>> _______________________________________________ >>>> Image-SIG maillist - [email protected] >>>> http://mail.python.org/mailman/listinfo/image-sig >>> > _______________________________________________ Image-SIG maillist - [email protected] http://mail.python.org/mailman/listinfo/image-sig