Re: Build PyQt5 from source with PyQt5-sip binary?

On Fri, Sep 20, 2019 at 01:49:56PM -0500, Zach Pincus wrote:
> I'm sorry if this is an obvious question, but I'm struggling a bit to
> build PyQt5 from sources on my Mac. (So that I may test the fixed
> onexit scheme from a nightly snapshot.)

pyqt5_enable_new_onexit_scheme() is part of the PyQt 5.13.1 release, so you
don't need to build anything from sources to test it.

> Anyhow, is there a way to get PyQt5-sip to produce an executable (or
> another straightforward way to get a sip binary / executable), or do I
> pretty much need to install sip from source (or from a package
> manager) in order to build PyQt5?

I always build it from source - it's quite painless and takes 5 seconds or so
to build.

Florian

-- 
https://www.qutebrowser.org | [email protected] (Mail/XMPP)
   GPG: 916E B0C8 FD55 A072 | https://the-compiler.org/pubkey.asc
         I love long mails! | https://email.is-not-s.ms/

_______________________________________________
PyQt mailing list    [email protected]
https://www.riverbankcomputing.com/mailman/listinfo/pyqt

-----BEGIN PGP SIGNATURE-----
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=CfMC
-----END PGP SIGNATURE-----