Re: EEG-SMT USB Interface

Here's a link to the source code for the IDE. It should be in there.

http://arduino.googlecode.com/files/arduino-1.0.2-src.tar.gz


On Fri, Nov 30, 2012 at 8:23 AM, David Warwick <[email protected]> wrote:

> On the FTDI website, it offers drivers to read it as a standard USB device
> via a DLL or .so instead of a virtual com port.  I installed libusb-win32
> and with my Java application, I am able to see the device EEG-SMT on a bus
> scan.  Though when I read from the device, the data is definitely not
> correct.  This does give me some hope to use libusb in Linux, but not being
> able to read the device is discouraging.  Though I will try to install the
> Linux FTDI drivers and see if I can read it that way, but apparently I have
> to change the EEPROM to do so.****
>
> ** **
>
> Anyway, I’m not 100% convinced that I can’t read it as a standard USB
> device, but I haven’t gotten it to work yet.  ****
>
> ** **
>
> Also, I haven’t tinkered around with Arduino.  Where would I find this
> code to which you refer?****
>
> ** **
>
> ** **
>
> ** **
>
> ** **
>
> *From:* William Shipley [mailto:[email protected]]
> *Sent:* Thursday, November 29, 2012 1:57 AM
> *To:* Discussion of EEG hardware, software, training protocols, NFB
> theory - for developers and users.
> *Subject:* Re: [Openeeg-list] EEG-SMT USB Interface****
>
> ** **
>
> No, you can't make the EEG show up as anything but a serial port. The COM
> port behavior is a hardware thing. Specifically, it's an FTDI chip. You'd
> have to ask the user which COM port it is, similar to how the arduino
> environment does on the older boards. In fact, it's the same chip, so you
> could probably use a lot of the arduino's code.****
>
> ** **
>
> On Tue, Nov 27, 2012 at 11:08 PM, David Warwick <[email protected]>
> wrote:****
>
> Is it possible to set the USB interface on the EEG-SMT to be a generic
> device that is not a COM port?  ****
>
> ** **
>
> I've written a Java based EEG reader in Linux for Stefan Jung's EXG2, and
> I'd like to also use the EEG-SMT.  The EEG-SMT does not show up in a USB
> device scan, so I'm not able to discern the vendor and product ID.  ****
>
> ** **
>
> I don't have a lot of experience in writing device drivers, so apologies
> in advance if this has already been covered.****
>
> ** **
>
>
>
> ------------------------------------------------------------------------------
> Keep yourself connected to Go Parallel:
> INSIGHTS What's next for parallel hardware, programming and related areas?
> Interviews and blogs by thought leaders keep you ahead of the curve.
> http://goparallel.sourceforge.net
> _______________________________________________
> Openeeg-list mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/openeeg-list
> Go to the above address to change your
> subscription options, e.g unsubscribe.****
>
> ** **
>
>
> ------------------------------------------------------------------------------
> Keep yourself connected to Go Parallel:
> TUNE You got it built. Now make it sing. Tune shows you how.
> http://goparallel.sourceforge.net
> _______________________________________________
> Openeeg-list mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/openeeg-list
> Go to the above address to change your
> subscription options, e.g unsubscribe.
>
>

------------------------------------------------------------------------------
Keep yourself connected to Go Parallel: 
TUNE You got it built. Now make it sing. Tune shows you how.
http://goparallel.sourceforge.net